|
Ich denke, dass das Importproblem grundsätzlich im Zusammenh... Dans le forum Wie drucke ich das? (Hilfe zum Drucken) |
il y a 2 years |
|
Auf die angezeigten Werte am LCD würde ich mich nicht verlas... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 2 years |
|
Aliexpress Lieferzeiten sind derzeit jenseits von irgendetwa... Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 2 years |
|
Great work! This reminds me a little of our "Riesenrad" in V... Dans le forum Awesome prints (Hall Of Fame) |
il y a 2 years |
|
Wie liegt das Teil auf der Druckplatte?
Ich gehe davon aus... Dans le forum Wie drucke ich das? (Hilfe zum Drucken) |
il y a 2 years |
|
👍Thanks for the feedback! ...further good success! wbr, Karl Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Would you briefly summarize what were the most important cha... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Die Extrusion scheint auch recht unregelmässig. Hast Du scho... Dans le forum Wie drucke ich das? (Hilfe zum Drucken) |
il y a 2 years |
|
another option to place the spools: In any case, I would no... Dans le forum General discussion, announcements and releases |
il y a 2 years |
|
Ich verwende hauptsächlich die grob- und feiner strukturiert... Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 2 years |
|
Glasplatte wird nicht funktionieren, da der Sensor bzw. Nähe... Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 2 years |
|
I briefly checked the gcode (cube not printed) and found an ... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Try printing the 20x20x20mm calibration cube. If you still h... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Are you using original PrusaSlicer presets for your filament... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |
|
Meine ältere Konfiguration (Pi mit Octoprint, LAN Verbindung... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 2 years |
|
I concur with @diem and @andrewterry. New does not always ha... Dans le forum Assembly and first prints troubleshooting |
il y a 2 years |
|
"Ersatzwellen geordert" - Ich würde das Problem an Prusa (Pr... Dans le forum Hilfe zur Hardware, Firmware und Software |
il y a 2 years |
|
Nachtrag: Wenn Du die Verbindung testest - kommt da eine Feh... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 2 years |
|
IP würde ich mal so versuchen: 192.168.0.65 API -> siehe ... Dans le forum Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
il y a 2 years |
|
Sometimes the theoretical values (400) may differ from the p... Dans le forum User mods - OctoPrint, enclosures, nozzles, ... |
il y a 2 years |