|
Ich denke, dass das Importproblem grundsätzlich im Zusammenh... En el foro Wie drucke ich das? (Hilfe zum Drucken) |
hace 2 years |
|
Auf die angezeigten Werte am LCD würde ich mich nicht verlas... En el foro Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
hace 2 years |
|
Aliexpress Lieferzeiten sind derzeit jenseits von irgendetwa... En el foro Hilfe zur Hardware, Firmware und Software |
hace 2 years |
|
Great work! This reminds me a little of our "Riesenrad" in V... En el foro Awesome prints (Hall Of Fame) |
hace 2 years |
|
Wie liegt das Teil auf der Druckplatte?
Ich gehe davon aus... En el foro Wie drucke ich das? (Hilfe zum Drucken) |
hace 2 years |
|
👍Thanks for the feedback! ...further good success! wbr, Karl En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 2 years |
|
Would you briefly summarize what were the most important cha... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 2 years |
|
Die Extrusion scheint auch recht unregelmässig. Hast Du scho... En el foro Wie drucke ich das? (Hilfe zum Drucken) |
hace 2 years |
|
another option to place the spools: In any case, I would no... En el foro General discussion, announcements and releases |
hace 2 years |
|
Ich verwende hauptsächlich die grob- und feiner strukturiert... En el foro Hilfe zur Hardware, Firmware und Software |
hace 2 years |
|
Glasplatte wird nicht funktionieren, da der Sensor bzw. Nähe... En el foro Hilfe zur Hardware, Firmware und Software |
hace 2 years |
|
I briefly checked the gcode (cube not printed) and found an ... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 2 years |
|
Try printing the 20x20x20mm calibration cube. If you still h... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 2 years |
|
Are you using original PrusaSlicer presets for your filament... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 2 years |
|
Meine ältere Konfiguration (Pi mit Octoprint, LAN Verbindung... En el foro Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
hace 2 years |
|
I concur with @diem and @andrewterry. New does not always ha... En el foro Assembly and first prints troubleshooting |
hace 2 years |
|
"Ersatzwellen geordert" - Ich würde das Problem an Prusa (Pr... En el foro Hilfe zur Hardware, Firmware und Software |
hace 2 years |
|
Nachtrag: Wenn Du die Verbindung testest - kommt da eine Feh... En el foro Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
hace 2 years |
|
IP würde ich mal so versuchen: 192.168.0.65 API -> siehe ... En el foro Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
hace 2 years |
|
Sometimes the theoretical values (400) may differ from the p... En el foro User mods - OctoPrint, enclosures, nozzles, ... |
hace 2 years |