|
Título del Tema |
Foro |
|
Original Prusa MMU3 upgrade kit (for MK4) - Shipping soon? (1 viendo) Por Zakoplex hace 3 months | Último Mensaje: hace 3 mins
|
General discussion, announcements and releases |
|
|
|
Prusa Slicer - Define Start Location Por Andy89 hace 3 hours | Último Mensaje: hace 40 mins
|
PrusaSlicer |
|
|
|
MK4 PLA Stringing Por PEU hace 5 months | Último Mensaje: hace 45 mins
|
Assembly and first prints troubleshooting |
|
|
|
Filament Spool Tangled Por patrickho138 hace 11 months | Último Mensaje: hace 1 hour
|
Assembly and first prints troubleshooting |
|
|
|
print quality Por Robert hace 4 days | Último Mensaje: hace 1 hour
|
Input Shaper (MINI) |
|
|
|
Is this a sign of damp filament? Por Razor hace 4 days | Último Mensaje: hace 2 hours
|
Hardware, firmware and software help |
|
|
|
No Thumbnails since upgrade to 5.1.0 Por jweaver hace 2 hours | Último Mensaje: hace 2 hours
|
General discussion, announcements and releases |
|
|
|
XL shipping table? (1 viendo) Por Asus1357 hace 4 weeks | Último Mensaje: hace 2 hours
|
General discussion, announcements and releases |
|
|
|
Bye bye, Prusa (1 viendo) Por SeattleDavid hace 1 day | Último Mensaje: hace 2 hours
|
General discussion, announcements and releases |
|
|
|
Strategic view of Bambu & Prusa - Part 2 - Corporate Signaling Por SeattleDavid hace 4 weeks | Último Mensaje: hace 3 hours
|
General discussion, announcements and releases |
|
|
|
MMU3 Physical Buffer Size Por Mick7000 hace 21 hours | Último Mensaje: hace 3 hours
|
General discussion, announcements and releases |
|
|
|
What would you like to see in the 8-bit firmware? Por Jakub Dolezal hace 3 years | Último Mensaje: hace 3 hours
|
General discussion, announcements and releases |
|
|
|
Finally got a prusa. too bad i failed at putting it together Por BulletShogun hace 3 days | Último Mensaje: hace 3 hours
|
Assembly and first prints troubleshooting |
|
|
|
MK3S+ update auf Revo Kit - Thermofehler Por ben#03 hace 22 hours | Último Mensaje: hace 3 hours
|
Hilfe zur Hardware, Firmware und Software |
|
|
|
Mk4 IS Seam scar Por bpereira1984 hace 22 hours | Último Mensaje: hace 4 hours
|
Input Shaper (MK4) |
|
|
|
Not slicing as expected? Por TripleFJeff hace 14 hours | Último Mensaje: hace 4 hours
|
PrusaSlicer |
|
|
|
Voreinstellung Dateinamen im Slicer Por Horst Isele hace 3 years | Último Mensaje: hace 5 hours
|
Grossartige Drucke & Tipps zum Drucken |
|
|
|
Sehr schlechte Druckqualität Por Headshaker hace 2 weeks | Último Mensaje: hace 5 hours
|
Zusammenbau und Fehlersuche bei den ersten Druckversuchen |
|
|
|
Shimpent (not) included?... Por avi ostfeld hace 6 hours | Último Mensaje: hace 5 hours
|
General discussion, announcements and releases |
|
|