English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 40 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Just got a new MK3S+ but SD card doesn’t come ... Da dhiltonp on May 10, 22 2650 5 Koon After 3.11.0 firmware update: First Layer Z he... Da BrassEm on May 08, 22 2349 3 BrassEm Gaps and holes in first layer Da PRNTD_Lab on May 06, 22 3256 3 PRNTD_Lab I see someone says 'Ahh so close' - I think I ... Da AmBodach on May 05, 22 2131 4 AmBodach I can't start a print Da JustMe3D on May 05, 22 2330 4 Leumas New firmware: first layer calibration is broke... Da Eric E on May 05, 22 1777 3 Vitalii3D Are these normal sounds or did I do something ... Da MrWizard on May 05, 22 2720 8 MrWizard Filament dried 50c for 6 hours. Da bobstro on May 04, 22 2802 7 Wraith MK3S+ E-axis Assembly Step 54 - Can't tilt X-A... Answered Da DefaultGen on May 03, 22 1309 1 DefaultGen New kit printer build: first startup... reboot... Da Robin on May 01, 22 1811 4 glyphstone Filament scrapping the intake hole. Da RandyM9 on May 01, 22 1405 3 Dusty.Tools Garbage displayed on the LCD after a print Da tomatis on Apr 29, 22 5038 14 michael.t28 Next level first layer dial-in method Da RandyM9 on Apr 26, 22 3034 6 doctorg prusa mk3s+ y-motor holder Da RandyM9 on Apr 26, 22 2124 2 bboran FS-Lever Not Clearing Filament IR Sensor (Auto... Da Rjburt on Apr 25, 22 6619 15 ben_r_ Ahhh so close Da k1mu on Apr 24, 22 4171 14 Juggernaught Calibration failure after self test ok Da k1mu on Apr 24, 22 2310 3 Benik2 Perimeters layers are not smooth Da doctorg on Apr 22, 22 2192 3 3D Design Bro... Prints not sticking o right front side no matt... Da doctorg on Apr 22, 22 5574 14 Nerp Just Ordered MK3S+ Kit, will I need to grease ... Da doctorg on Apr 22, 22 2632 6 SaltyGentlema... Pagina 40 / 218 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Avanti Condividi: