English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 2 / 218 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Old STL file needed Por Neophyl on Aug 02 2804 3 Gavin Melvill... First layer starts then z calibration loop Por Diem on Jul 25 2725 2 Juan David Horizontal layer lines (Z-Banding?) Por Aaron O on Jul 18 16186 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Por printing_stuff on Jul 10 3195 9 printing_stuf... I bought a used printer and can't tell if it's... Por PrusaNewbie on Jul 10 3998 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Por HYspd on Jul 06 4538 2 Fourninetysix Z-Axis noise. Is this normal? Por Robin_13 on Jun 26 13850 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Por Kenyiro34 on Jun 20 3191 8 Blippio Test print doesn't print straight lines Por JoanTabb on May 30 4035 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Por Criptop on May 30 5837 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Por Cwhite534 on May 23 3571 7 jhk22 2nd Print with PLA takeoff from the plate Por JoanTabb on May 15 3931 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Por gigiga on May 06 5908 10 SeppoTakalo First layer PETG not sticking to print bed Answered Por tom_streeter on Apr 30 62988 26 Chuck Unable to Autoload Filament Por CodeCage on Apr 19 14914 9 gmbarton Last Mk3s+ to be built ? Por Dennis Jay on Apr 17 2278 2 Jws3d Superpinda keeps smacking print Por Eve on Apr 13 4506 2 CliffordTheRe... Inconsistent first layers after first few prin... Por Eve on Apr 13 4376 4 Eve Ultrasonic Cleaner on new bearings? Por TeamADW on Apr 09 4960 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Por Jake on Mar 21 4482 3 Jake Página 2 / 218 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Siguiente Compartir: