English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Stringy Benchy Answered Por DartagnanK on hace 4 days 191 3 DartagnanK printhead does not extrude after an hour in pr... Por Diem on Aug 29 296 2 Elzpirat Weird first layer issues Answered Por Heather Mac Le... on Aug 21 13355 7 Skint007 Bed leveling/underextrusion Por perspectives08... on Aug 20 523 1 perspectives0... XYZ Calibration failed, check axes Por Maksim Drachov on Aug 16 11073 19 rgordon0 life adjust Z - my way Answered Por Carolina Custo... on Aug 13 994385 1012 JeffJordan Old STL file needed Por Neophyl on Aug 02 794 3 Gavin Melvill... First layer starts then z calibration loop Por Diem on Jul 25 954 2 Juan David Horizontal layer lines (Z-Banding?) Por Aaron O on Jul 18 14849 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Por printing_stuff on Jul 10 1529 9 printing_stuf... I bought a used printer and can't tell if it's... Por PrusaNewbie on Jul 10 3080 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Por HYspd on Jul 06 4125 2 Fourninetysix Z-Axis noise. Is this normal? Por Robin_13 on Jun 26 12576 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Por Kenyiro34 on Jun 20 2725 8 Blippio Test print doesn't print straight lines Por JoanTabb on May 30 3036 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Por Criptop on May 30 5330 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Por Cwhite534 on May 23 3054 7 jhk22 2nd Print with PLA takeoff from the plate Por JoanTabb on May 15 2790 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Por gigiga on May 06 5217 10 SeppoTakalo First layer PETG not sticking to print bed Answered Por tom_streeter on Apr 30 58977 26 Chuck Página 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: