English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Stringy Benchy Answered Przez DartagnanK on 3 days temu 151 3 DartagnanK printhead does not extrude after an hour in pr... Przez Diem on Aug 29 261 2 Elzpirat Weird first layer issues Answered Przez Heather Mac Le... on Aug 21 13341 7 Skint007 Bed leveling/underextrusion Przez perspectives08... on Aug 20 492 1 perspectives0... XYZ Calibration failed, check axes Przez Maksim Drachov on Aug 16 11065 19 rgordon0 life adjust Z - my way Answered Przez Carolina Custo... on Aug 13 993896 1012 JeffJordan Old STL file needed Przez Neophyl on Aug 02 764 3 Gavin Melvill... First layer starts then z calibration loop Przez Diem on Jul 25 924 2 Juan David Horizontal layer lines (Z-Banding?) Przez Aaron O on Jul 18 14839 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Przez printing_stuff on Jul 10 1499 9 printing_stuf... I bought a used printer and can't tell if it's... Przez PrusaNewbie on Jul 10 3050 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Przez HYspd on Jul 06 4116 2 Fourninetysix Z-Axis noise. Is this normal? Przez Robin_13 on Jun 26 12565 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Przez Kenyiro34 on Jun 20 2720 8 Blippio Test print doesn't print straight lines Przez JoanTabb on May 30 3006 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Przez Criptop on May 30 5321 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Przez Cwhite534 on May 23 3047 7 jhk22 2nd Print with PLA takeoff from the plate Przez JoanTabb on May 15 2760 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Przez gigiga on May 06 5203 10 SeppoTakalo First layer PETG not sticking to print bed Answered Przez tom_streeter on Apr 30 58947 26 Chuck Strona 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: