English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Stringy Benchy Answered Da DartagnanK on 3 days fa 164 3 DartagnanK printhead does not extrude after an hour in pr... Da Diem on Aug 29 276 2 Elzpirat Weird first layer issues Answered Da Heather Mac Le... on Aug 21 13347 7 Skint007 Bed leveling/underextrusion Da perspectives08... on Aug 20 504 1 perspectives0... XYZ Calibration failed, check axes Da Maksim Drachov on Aug 16 11068 19 rgordon0 life adjust Z - my way Answered Da Carolina Custo... on Aug 13 994089 1012 JeffJordan Old STL file needed Da Neophyl on Aug 02 775 3 Gavin Melvill... First layer starts then z calibration loop Da Diem on Jul 25 935 2 Juan David Horizontal layer lines (Z-Banding?) Da Aaron O on Jul 18 14844 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Da printing_stuff on Jul 10 1510 9 printing_stuf... I bought a used printer and can't tell if it's... Da PrusaNewbie on Jul 10 3061 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Da HYspd on Jul 06 4118 2 Fourninetysix Z-Axis noise. Is this normal? Da Robin_13 on Jun 26 12570 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Da Kenyiro34 on Jun 20 2723 8 Blippio Test print doesn't print straight lines Da JoanTabb on May 30 3017 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Da Criptop on May 30 5323 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Da Cwhite534 on May 23 3052 7 jhk22 2nd Print with PLA takeoff from the plate Da JoanTabb on May 15 2771 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Da gigiga on May 06 5212 10 SeppoTakalo First layer PETG not sticking to print bed Answered Da tom_streeter on Apr 30 58957 26 Chuck Pagina 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: