English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 1 / 212 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 Next Topic Title Last Post Views Posts Author First Layer calibration failing By AppleSauce on 15 hours ago 86 1 AppleSauce Front Print Fan fails selftest but is spinning By Artur5 on 2 days ago 1070 3 MyNameIsBrad Noisy bed on MK3S By charlesplamond... on 3 days ago 4581 20 Alex life adjust Z - my way Answered By GP24Z7 on 5 days ago 776949 991 JeffJordan X and Y axis Hesitation - New MK3S+ By Trey Walker on Mar 22 228 1 Trey Walker Unable to find home (can't reset origin) By Estes Valley L... on Mar 19 502 9 Estes Valley ... First Layer Bubbling(?) in same spot on print ... By SteveC on Mar 19 500 12 SteveC Wavy Walls By Max Schuh on Mar 17 3557 17 ellaine Bad first layer print By Bob on Mar 14 696 3 Michael Oakle... Weird offset / missteps on Z axis or extrusion... By nio101 on Mar 10 680 9 nio101 Another XYZ calibration fail By troconn on Mar 09 3736 9 Asher Printing of prusa parts. By Bob on Mar 07 612 2 Wazfoodle Z axis calibration Answered By Marek Jaros on Mar 06 897 5 Marek Jaros X Shift on Recently upgraded mk3s+ By Robin on Mar 06 714 3 Graeme Johans... The Base Showing Up On The External Layer By Robin on Mar 06 629 2 LeeH Can't remove attached cable from motherboard..... By bobnosn on Mar 03 2174 10 PrusaVA Calibration failed, check axis and run again By Robin on Mar 01 795 2 Kraut55 Extruder destroyed the PIDA mount By Robin on Feb 28 982 11 jlc1978 extruder stops turning mid print By tigertrainer on Feb 27 958 7 tigertrainer Extruder parks at 0 when print is done. By Logan Elswick on Feb 24 943 3 Logan Elswick Page 1 / 212 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 Next Share: