English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 2 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author X-Axis Motor Cable Too Short / Binding the Z-A... Przez Criptop on May 30 5554 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Przez Cwhite534 on May 23 3275 7 jhk22 2nd Print with PLA takeoff from the plate Przez JoanTabb on May 15 3808 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Przez gigiga on May 06 5468 10 SeppoTakalo First layer PETG not sticking to print bed Answered Przez tom_streeter on Apr 30 60306 26 Chuck Unable to Autoload Filament Przez CodeCage on Apr 19 13999 9 gmbarton Last Mk3s+ to be built ? Przez Dennis Jay on Apr 17 2083 2 Jws3d Superpinda keeps smacking print Przez Eve on Apr 13 4240 2 CliffordTheRe... Inconsistent first layers after first few prin... Przez Eve on Apr 13 4112 4 Eve Ultrasonic Cleaner on new bearings? Przez TeamADW on Apr 09 4476 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Przez Jake on Mar 21 4174 3 Jake First layer cal is way off Przez Diem on Mar 13 3775 5 Bjerggaard No successful print so far Przez FoxRun3D on Feb 28 3431 4 boricuastock Calibration Wizard question Przez SWAG_4_1if3 on Feb 27 3435 3 SWAG_4_1if3 Whenever I run out of filament - I have to dis... Przez dankat on Feb 25 4514 11 Mattias Fager... Argh! It keeps asking me to unload and reload... Przez Deeb on Feb 22 19421 41 dimprov Priline Carbon Fiber Polycarbonate Not Good Przez 3D2Reality on Feb 22 12964 14 Degreeless_En... Underextrusion / no extrusion at start of each... Przez Green Joe on Feb 20 4313 5 Don Karnage XYZ Calibration Cube Przez Robin_13 on Feb 17 2602 3 Iamcubsman PTFE tube Przez Robin_13 on Feb 17 1843 4 Leo Strona 2 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: