English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 2 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Von HYspd on Jul 06 4413 2 Fourninetysix Z-Axis noise. Is this normal? Von Robin_13 on Jun 26 13329 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Von Kenyiro34 on Jun 20 3003 8 Blippio Test print doesn't print straight lines Von JoanTabb on May 30 3879 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Von Criptop on May 30 5650 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Von Cwhite534 on May 23 3387 7 jhk22 2nd Print with PLA takeoff from the plate Von JoanTabb on May 15 3843 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Von gigiga on May 06 5644 10 SeppoTakalo First layer PETG not sticking to print bed Answered Von tom_streeter on Apr 30 61288 26 Chuck Unable to Autoload Filament Von CodeCage on Apr 19 14324 9 gmbarton Last Mk3s+ to be built ? Von Dennis Jay on Apr 17 2172 2 Jws3d Superpinda keeps smacking print Von Eve on Apr 13 4345 2 CliffordTheRe... Inconsistent first layers after first few prin... Von Eve on Apr 13 4196 4 Eve Ultrasonic Cleaner on new bearings? Von TeamADW on Apr 09 4636 8 Bill Marcy Printer Failing Z-Axis Test With No Error Mess... Von Jake on Mar 21 4279 3 Jake First layer cal is way off Von Diem on Mar 13 3859 5 Bjerggaard No successful print so far Von FoxRun3D on Feb 28 3494 4 boricuastock Calibration Wizard question Von SWAG_4_1if3 on Feb 27 3462 3 SWAG_4_1if3 Whenever I run out of filament - I have to dis... Von dankat on Feb 25 4677 11 Mattias Fager... Argh! It keeps asking me to unload and reload... Von Deeb on Feb 22 19900 41 dimprov Seite 2 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: