English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 2 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Tytuł Tematu Ostatni Post Widok Posty Author Preheat error Przez Miloš Vidakovi... on Sep 21 3457 1 Miloš Vidakov... Broken Hotend Thermistor Wire Przez JMars on Sep 20 15967 8 Patrick Stringy Benchy Answered Przez DartagnanK on Sep 04 3670 3 DartagnanK Weird first layer issues Answered Przez Heather Mac Le... on Aug 21 15166 7 Skint007 Bed leveling/underextrusion Przez perspectives08... on Aug 20 2730 1 perspectives0... XYZ Calibration failed, check axes Przez Maksim Drachov on Aug 16 12582 19 rgordon0 life adjust Z - my way Answered Przez Carolina Custo... on Aug 13 1050397 1012 JeffJordan Old STL file needed Przez Neophyl on Aug 02 2883 3 Gavin Melvill... First layer starts then z calibration loop Przez Diem on Jul 25 2798 2 Juan David Horizontal layer lines (Z-Banding?) Przez Aaron O on Jul 18 16797 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered Przez printing_stuff on Jul 10 3399 9 printing_stuf... I bought a used printer and can't tell if it's... Przez PrusaNewbie on Jul 10 4140 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... Przez HYspd on Jul 06 4716 2 Fourninetysix Z-Axis noise. Is this normal? Przez Robin_13 on Jun 26 14365 19 Muldjord Y Axis Length Fail on Bear MK3S+ build Przez Kenyiro34 on Jun 20 3363 8 Blippio Test print doesn't print straight lines Przez JoanTabb on May 30 4212 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... Przez Criptop on May 30 6006 8 Matt Kurek Printer goes to centre of build plate after ev... Answered Przez Cwhite534 on May 23 3793 7 jhk22 2nd Print with PLA takeoff from the plate Przez JoanTabb on May 15 4079 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... Przez gigiga on May 06 6269 10 SeppoTakalo Strona 2 / 218 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Następny Share: