| |
Topic Title |
Forum |
 |
Mk4 Display Cable to short for the Prusa Original Enclosure? By M 3 years ago | Last Post: 3 days ago
|
User mods - OctoPrint, enclosures, nozzles, ... |
|
 |
Buddy Cam Core One Wifi connection failed after update to FW 3.1.2 By RalfD 4 months ago | Last Post: 3 days ago
|
Buddy3D |
|
 |
Core One+ randomly restarts about 10-15 seconds after starting a new print By nicknormal 4 days ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
using prusa slicer. By rjb2222 4 days ago | Last Post: 4 days ago
|
How do I print this? (Printing help) |
|
 |
Bad ribbed models. (prusaslicers fault) By Alienbliep 5 days ago | Last Post: 4 days ago
|
How do I print this? (Printing help) |
|
 |
Instead of COREBOXX or INBXX... how about PrusaExoskeletonBXX ? By Wejn 2 weeks ago | Last Post: 4 days ago
|
User mods |
|
|
|
Multi Color Filamnets on a Mini Prusa - MMU By eager 4 days ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
6.4.1 Beta Firmware for the Prusa XL By Jan Kratochvíl 1 week ago | Last Post: 4 days ago
|
General discussion, announcements and releases |
|
 |
Nozzle clean failed, at start of print. By LOQuin 4 days ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
problems Implementing filtration system utilizing fan 3 of the buddy expansion board By Lynn 4 days ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
Remove adhesive from the Core One front acrylic panel By Jascha3D 6 days ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
SSL_CERT_FILE not set By Markov 4 months ago | Last Post: 4 days ago
|
PrusaSlicer |
|
 |
Issues with belt tuning and Nextruder By Parker 5 days ago | Last Post: 4 days ago
|
Assembly and first prints troubleshooting |
|
|
|
Can't insert new filament after unloading the old one By Chaz Ashley 6 days ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
Core One with INDX width By Oscar_MV 6 days ago | Last Post: 4 days ago
|
General discussion, announcements and releases |
|
 |
Core One MMU3 Filament unloading getting stuck By Kevin Maxey 6 months ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
Extruder skipping By atlantis7 6 months ago | Last Post: 4 days ago
|
Hardware, firmware and software help |
|
 |
XL: Filament Dryboxes By flounder 2 years ago | Last Post: 4 days ago
|
General discussion, announcements and releases |
|
 |
Buddy Camera in the Core one reads the code and shows up in Connect, but is not registered. By Dik Harrison 6 months ago | Last Post: 4 days ago
|
General discussion, announcements and releases |
|
 |
8 Spulenhalter By Peter Gasper 4 days ago | Last Post: 4 days ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
|