| |
Topic Title |
Forum |
 |
Position parking By Legnano 2 years ago | Last Post: 18 hours ago
|
Aide concernant le matériel, le firmware ou un logiciel |
|
 |
What are the differences between a 3.5 and a 3.5s By mpatl 5 months ago | Last Post: 20 hours ago
|
General discussion, announcements and releases |
|
 |
First layer is too low MK4S By FireBlast2.0 2 days ago | Last Post: 20 hours ago
|
Assembly and first prints troubleshooting |
|
 |
MK4S problém s TPU By TheCenda 20 hours ago | Last Post: 20 hours ago
|
Hardware, firmware a software (Pomoc) |
|
 |
Recent temperature fluctuations By ImAlias 22 hours ago | Last Post: 22 hours ago
|
Hardware, firmware and software help |
|
 |
New XL: Pin not reached #17107 on 2. tool By Dr_H 1 day ago | Last Post: 22 hours ago
|
Assembly and first prints troubleshooting |
|
 |
Stuck on Chapter 3, Step 19 - Nut turning in slot By jarias 1 month ago | Last Post: 23 hours ago
|
Assembly and first prints troubleshooting |
|
 |
Filament mitten im Druck nachlegen? Probleme mit Nachlaufen! By Cossman 2 days ago | Last Post: 23 hours ago
|
Hilfe zur Hardware, Firmware und Software |
|
 |
Thermal Error/Anomaly/Runaway Issue By Tas_The_Bunny 23 hours ago | Last Post: 23 hours ago
|
Hardware, firmware and software help |
|
 |
Nozzle scratches over print after tool change By Koet 23 hours ago | Last Post: 23 hours ago
|
How do I print this? (Printing help) |
|
 |
Xl extruder stops By cucuy666 11 months ago | Last Post: 23 hours ago
|
Hardware, firmware and software help |
|
 |
Bulge when print reaches "solid" layers By Nicolai 6 years ago | Last Post: 24 hours ago
|
How do I print this? (Printing help) |
|
 |
Printer nags to update firmware By rickwise 4 days ago | Last Post: 1 day ago
|
General discussion, announcements and releases |
|
 |
Prusa Core One - Intial thoughts...... By iftibashir 1 month ago | Last Post: 1 day ago
|
General discussion, announcements and releases |
|
 |
Drucker nimmt Filament von fragilem Druck beim first layer mit By KaptainAhoibrause 4 days ago | Last Post: 1 day ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
|
 |
MMU Board first start and no life signal By l1thium 1 week ago | Last Post: 1 day ago
|
Hardware, firmware and software help |
|
 |
Retour Prusa XL By Cachou 9 months ago | Last Post: 1 day ago
|
Discussion générale, annonces et nouveautés |
|
 |
Z callibration failure no matter where the PINDA is set or adjusted, even after replacing it. By MegardStudio 2 weeks ago | Last Post: 1 day ago
|
Hardware, firmware and software help |
|
 |
Vertical artifact when printing with 0.15 height layers By Julien 3 days ago | Last Post: 1 day ago
|
Assembly and first prints troubleshooting |
|
 |
MK4S: PLA type am Drucker umstellen. By SatMAX 2 weeks ago | Last Post: 1 day ago
|
Allgemeine Diskussion, Ankündigungen und Veröffentlichungen |
|