English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 24 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author Printing ribs to help parts fit Przez FoxRun3D on Jun 13, 23 1869 4 epzcaw Advice on printing this item Przez Tango on Jun 12, 23 4078 15 Tango Clearance data Przez epzcaw on Jun 11, 23 3110 5 epzcaw Can't figure out this error - corners lifting ... Przez jsw on Jun 11, 23 4744 13 Chris Print Adhesion issue in lower left corner of b... Przez jessestephens1... on Jun 10, 23 1447 1 jessestephens... Printing TPU on Smooth Sheet on MK3S+? Answered Przez SGBen on Jun 10, 23 3816 15 3DCoded Vase mode-> 4th layer is squeezed for some odd... Przez Robin on Jun 10, 23 1707 3 Roshan Varkey Clapped-Out Mk3 restoration help Przez Robin on Jun 09, 23 1750 4 James Sutherl... [Solved] Filament jams each time at same point Przez AnneVanLeyden on Jun 09, 23 2282 2 AnneVanLeyden Tall print knocked over Przez AnneVanLeyden on Jun 09, 23 3256 6 Siggi Bjarnas... Wall thickness not integer extrusion widths Przez JoanTabb on Jun 08, 23 2062 10 DanielNorling Some help with my prints!!? Przez Cycleman on Jun 08, 23 1330 1 Cycleman Steel Sheet problems - Do not stick Answered Przez jsw on Jun 05, 23 2017 5 Stonefox Slicer settings for LW-PLA RC Aircraft Przez DaveE128 on Jun 05, 23 10401 9 Robcarp Prusa Slicer fills in hole in my model - Manif... Answered Przez gedeyenite on Jun 01, 23 11285 11 dan007 Inconsistent Nylon Heat Creep Failure Przez RyDude575 on Jun 01, 23 2632 4 RyDude575 I am getting continous y-crashes with prusamen... Przez Ganymed on May 31, 23 3166 1 Ganymed Under Extrusion at Start of Some Middle Layers Przez Lloyd Welder on May 31, 23 2913 2 Lloyd Welder [MK3S] First layer issue proggressively worsen... Przez Katakana54 on May 30, 23 2515 5 Katakana54 Prusacaster - warping of the core part Przez Milos V. on May 28, 23 2619 2 Milos V. Strona 24 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: