English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 25 / 187 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Następny Tytuł Tematu Ostatni Post Widok Posty Author Holes at seams Przez pixelwave on Apr 01, 23 2720 4 Derek ONLY Top layers have wavy/over extruded mess Przez fprumbau on Apr 01, 23 7915 12 Telz Potential Under-Extrusion at the Perimeter Przez JasonMakesStuf... on Mar 30, 23 1969 7 JasonMakesStu... Layerneer on smooth PEI? Przez cwbullet on Mar 30, 23 1204 4 Orange Joe Acceleration or jerk bounds for heavy prints? Answered Przez Anachronist on Mar 30, 23 3480 5 cooperised Just Bad Prints Przez Jeffrey Dawson on Mar 29, 23 1085 1 Jeffrey Dawso... Issues with printing file Przez Evgeniy on Mar 29, 23 989 1 Evgeniy top layer warping on box Przez Blarge1513 on Mar 29, 23 1025 1 Blarge1513 Curling & Nozzle crash issues with specific mo... Przez frost on Mar 28, 23 1450 3 frost Flame-Retardant Capabilities Przez Stefan on Mar 28, 23 1450 2 BParr4 Issue printing simple 3 part design Przez FoxRun3D on Mar 27, 23 1340 2 Chris Print speed by layer Answered Przez addohm on Mar 27, 23 2459 10 addohm Printing hoverangs in a corkscrew conveyor Przez Galinette on Mar 25, 23 1394 1 Galinette Reducing staircase effect without lowering the... Przez Galinette on Mar 24, 23 968 1 Galinette Issue with rough top infill edges on 0.6mm noz... Przez Mark Hähnel on Mar 22, 23 1216 1 Mark Hähnel Issues printing TPU Przez ssill2 on Mar 20, 23 5898 14 Slayer Looks good, prints bad Przez Rajah on Mar 20, 23 1640 5 Rajah Flat areas not consistent Przez Diem on Mar 20, 23 1658 4 CupCap Vase Mode - Unexpected Nozzle Movement Answered Przez broconne on Mar 19, 23 1087 4 broconne Print Wont stick to bed? curling sometimes Przez jsw on Mar 19, 23 1966 7 cin05bus Strona 25 / 187 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 Następny Share: