English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 96 / 218 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Bearing installation Por jluvs2ride on Oct 19, 20 4009 17 jluvs2ride Persistent thermal runaway Por jurassic73 on Oct 19, 20 5618 19 Lingomat Issues when printing first layer of 0.3mm or m... Por JE Suza on Oct 19, 20 6107 9 JE Suza Very sloppy first prints Answered Por -- on Oct 18, 20 2399 8 Hotblack43 First prints, sizes problems Por -- on Oct 18, 20 2001 6 lekonna 3D Benchy Issue: Horizontal lines evenly space... Por -- on Oct 17, 20 17786 11 DespairFlare Problem of my first sword print Por -- on Oct 17, 20 4769 4 AC My printed lines are slightly wavy Por -- on Oct 16, 20 4963 5 Amlughelke "Finished" and I'm terrified I failed on fan s... Por jwvaughn on Oct 16, 20 2164 4 citizen458931 Extrusion stops after ~2-5cm printing Por -- on Oct 16, 20 1888 4 nssalee During printing strange sound when printing in... Por Area51 on Oct 15, 20 2609 6 Erwin First Time Ever 3d Printing Por Switch626 on Oct 15, 20 2225 4 Switch626 First prints critique needed Por Dink on Oct 14, 20 1670 1 Dink I think my PINDA Sensor has Failed Por Fredericc on Oct 14, 20 3620 9 Jeff Sticking pattern on the surface of round objec... Por Rahim42 on Oct 13, 20 1905 3 Rahim42 Lubricant prusa i3 mk3 Por kasswassim on Oct 13, 20 1644 3 kasswassim First Layer Calibration is different from slic... Por sophie.ke on Oct 13, 20 2938 6 sophie.ke Various printing issues / do I have a bad prin... Por bobstro on Oct 12, 20 2321 2 bobcat19 Filament not extruding Por ekmek on Oct 11, 20 18398 16 marcel.f2 MK3 Carriage screws Por CopyRunStart on Oct 11, 20 1858 1 CopyRunStart Página 96 / 218 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Siguiente Compartir: