English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 96 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Extrusion stops after ~2-5cm printing Od -- on Oct 16, 20 1710 4 nssalee During printing strange sound when printing in... Od Area51 on Oct 15, 20 2419 6 Erwin First Time Ever 3d Printing Od Switch626 on Oct 15, 20 2029 4 Switch626 First prints critique needed Od Dink on Oct 14, 20 1471 1 Dink I think my PINDA Sensor has Failed Od Fredericc on Oct 14, 20 3274 9 Jeff Sticking pattern on the surface of round objec... Od Rahim42 on Oct 13, 20 1653 3 Rahim42 Lubricant prusa i3 mk3 Od kasswassim on Oct 13, 20 1466 3 kasswassim First Layer Calibration is different from slic... Od sophie.ke on Oct 13, 20 2602 6 sophie.ke Various printing issues / do I have a bad prin... Od bobstro on Oct 12, 20 2117 2 bobcat19 Filament not extruding Od ekmek on Oct 11, 20 17314 16 marcel.f2 MK3 Carriage screws Od CopyRunStart on Oct 11, 20 1660 1 CopyRunStart MK3s New build. X axis failed Od Mike on Oct 11, 20 1965 4 Mike Discrepancy between PRUSA test logo and Benchy Od AWilling on Oct 11, 20 2044 1 AWilling Issue with Filamentum Crystal Clear Od cwbullet on Oct 10, 20 4730 23 ceceppa Extruding too much filament before printing? Od Andy on Oct 10, 20 9230 12 paul.a13 My first Benchy Od KZG on Oct 09, 20 4537 11 KZG nylon guide assembly Od Zoltan on Oct 09, 20 5640 6 gavin_the_new... First Layer Calibration Problem Od GKMAKEIT on Oct 08, 20 3031 10 M.J. Caboose Am I squishing the first layer too much? Od Ken S. on Oct 08, 20 4554 4 Ken S. First Layer Perimeter Errors Od ealtabet on Oct 06, 20 2679 3 ealtabet Stránka 96 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: