English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifiche Cancella tutti Assembly and first prints troubleshooting | RSS Pagina 53 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Issues loading filament Da Waresdom on Nov 23, 21 1390 1 Waresdom Issues with first layer adhesion/dragging Da Diem on Nov 23, 21 1767 5 cjmm First layer issue need advice on this please Da Othila on Nov 23, 21 1346 9 Othila Spare parts questions Da jsw on Nov 23, 21 1676 6 topdotter XYZ calibration print head too low; First laye... Da Dan Rogers on Nov 23, 21 1605 5 topdotter First layer opinion Da Buzz on Nov 22, 21 1753 6 Buzz Strange machine behaviour... No filament comin... Da Basic on Nov 21, 21 1916 12 Basic XYZ Calibration failed refer to manual Da Design Elevato... on Nov 20, 21 2481 16 Arne Bed Level Correction assistance Da shikaku201 on Nov 20, 21 2724 10 shikaku201 Is Ethyl Alchohol 70% OK for cleaning? Or it h... Da Eric E on Nov 19, 21 6687 6 Samut First few weeks of prints Da Diem on Nov 19, 21 1746 3 Buzz Brand new factory assembled mk3s+. Z axis much... Da Kuri on Nov 18, 21 2968 5 Kuri A 38x42 mm. hollow cylinder takes 6 hours 36 m... Da Neophyl on Nov 17, 21 2531 9 Samut First benchy after assembly Da Diem on Nov 17, 21 1741 3 Chealton Filament Not Extruding Da kwp1989 on Nov 17, 21 1829 5 PeterArnoldDe... One of My First Prints - Weird Result Da Dan Rogers on Nov 16, 21 1906 5 SureLockEscap... KIT first time calibration X-axis failure Da Aaron the Warm... on Nov 16, 21 1937 5 Aaron the War... Oil marks on print bed + noise from motor Da sylviatrilling on Nov 16, 21 1649 2 Geehoon First benchy after MK3S+ assembly. Any tips? Da Dan Rogers on Nov 15, 21 1658 2 Beefmagigins First Benchy print after assembly of MK3S+ Da Diem on Nov 15, 21 1446 4 Beefmagigins Pagina 53 / 217 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Avanti Condividi: