English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 53 / 216 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author x axis shift Od Diem on Nov 07, 21 953 3 Dahlia503 What would cause these horizontal lines? Od BogdanH on Nov 07, 21 1661 2 SwimClips Stringing issues with prusament Od zzjlamb on Nov 06, 21 4967 8 StrangelyType... Error: axis length X Answered Od R. Jonas on Nov 05, 21 1019 3 R. Jonas Long tail and zigzag Od Neophyl on Nov 04, 21 1210 5 enkumi Bed Level Correction Test- Center & Center Lef... Od Dan Rogers on Nov 04, 21 1162 6 Knarfly Ninjatek Cheetah Settings for PrusaSlicer Od Dangc10 on Nov 03, 21 5749 3 davisjc22 Self-Destructing Printer Od HakunaMatata on Nov 03, 21 1564 12 Touchstone Troubles calibrating Z axis Answered Od whereishere on Nov 02, 21 1357 10 whereishere Top layer issues (not printing smooth) Od sylviatrilling on Nov 02, 21 4343 7 theDSK Blobs at the retract positions Od Ringarn67 on Nov 01, 21 2315 7 the-powl clicks after one hour of printing with 0.25mm ... Od Dan Rogers on Oct 30, 21 1403 4 lmgoes catastrophic failure Od JoanTabb on Oct 29, 21 2817 8 Jerry S No power after initial heat up.. Od TheCrow13 on Oct 27, 21 797 4 TheCrow13 Extrusion Maybe? Od JCardoso on Oct 27, 21 1231 8 JCardoso Z axis calibration problems Answered Od Dan Rogers on Oct 27, 21 1328 3 Hamsmith MK3S X-axis Shifting? Od Dan Rogers on Oct 27, 21 1769 11 Touchstone Burnmarks Od okessler on Oct 26, 21 1600 7 okessler Layer separation in corners Od BogdanH on Oct 25, 21 1704 5 Gaute Assembly instruction manual - suggestion Od John_C on Oct 23, 21 1254 3 John_C Stránka 53 / 216 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Další Share: