English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 36 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Titre du sujet Dernier message Nombre de vues Messages Author Uneven extrusion after troubleshooting Par Diem on Jul 07, 22 2279 4 doveilgatto First Layer Problem Par Nate on Jul 07, 22 1802 5 Nate disappointed with the mk3s Par Diem on Jul 06, 22 1956 6 leandro.pitta All going well until one print... Par JoanTabb on Jul 04, 22 2087 8 Tango Filament not recognized (any more?) Answered Par karl-herbert on Jul 04, 22 1669 4 Tom Not quite first print, but possible adjustment... Par Tango on Jul 02, 22 1499 1 Tango First benchy and ctrlV test, small issues Answered Par Diem on Jul 02, 22 2188 6 eJar0k Couple hot end questions Par jmshirley on Jul 01, 22 1538 3 jmshirley 3rd print - not much on the bottom layer Answered Par Tango on Jun 29, 22 1864 4 Tango Over a day and a half to print this?!? Par Tango on Jun 28, 22 1977 4 Tango Y axis length error Par Robin on Jun 26, 22 1805 4 Krashone Just assembled and calibration prints have pro... Par Robin on Jun 26, 22 6696 23 Tango Starts printing at 23.15mm ?? Par KikeMarchuet on Jun 25, 22 2062 6 KikeMarchuet Heat bed alignment Par JoanTabb on Jun 24, 22 1983 4 Nateclaf A vey unhappy experience. Par Crab on Jun 24, 22 5711 38 Baz TPU Print - Extruded missing steps or nozzle j... Par theDSK on Jun 22, 22 2239 1 theDSK Underextrusion after nozzle change Par karpeychik on Jun 21, 22 1995 3 karpeychik Newbie needs help! Can't even start the self-t... Par cwbullet on Jun 21, 22 2577 8 wealthychef material going out of nozzle while heating up ... Par lepo on Jun 16, 22 12151 13 PDG Problems with ironing Par Martin_AUT on Jun 16, 22 2143 1 Martin_AUT Page 36 / 217 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Suivant Partager :