English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 20 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Odd XYZ Calibration Issue Answered Przez Alex Wait on Feb 18, 23 1307 3 Alex Wait XYZ calibration failure Przez Nimitz on Feb 17, 23 1485 3 Nimitz Another first layer problem. Przez budgie on Feb 16, 23 1495 3 budgie Printing a replacement part, and minor 1st pri... Przez RandyM9 on Feb 15, 23 1441 8 Culprit First layer - very unsatisfactory results Answered Przez karl-herbert on Feb 14, 23 1418 4 skaddisbladis Test print looks a bit odd Przez Diem on Feb 14, 23 1476 7 elan Fresh setup – continuous beeping Przez Diem on Feb 13, 23 1834 4 Wolf Stringing worse than my ender 3 with same sett... Przez danifrancescon on Feb 12, 23 2069 7 danifrancesco... First layer not constant in time Przez gagou7 on Feb 12, 23 1227 5 gagou7 Newbie question regarding z-axis calibration Answered Przez James McCullou... on Feb 11, 23 1538 10 James McCullo... clogged nozzle on mk3s+ Przez Robin on Feb 10, 23 1539 2 RMIL loud x axis motor Przez Hello on Feb 09, 23 1477 2 Dawnbringer6 Warping and temporary layer shift Answered Przez Mihai Dincules... on Feb 07, 23 1340 4 Mihai Dincule... Trouble with Z calibration? Przez Matt Sheets on Feb 05, 23 1082 3 Matt Sheets Z wobbling and shifted layer on overhangs Przez Thomas Cheng on Feb 04, 23 1866 12 Thomas Cheng hotted temp not settling even after a PID Przez Hello on Feb 03, 23 1090 2 willeykj Missin top layer? Przez karl-herbert on Feb 03, 23 1435 13 GrandPa Dragging through layer Przez Jonathan Leek on Feb 02, 23 1381 3 Jonathan Leek Weird finish on first layer Answered Przez Toochi on Feb 02, 23 1330 3 Toochi Printing a tube 120 mm diameter - print is und... Przez SG Newb Rider on Feb 01, 23 1718 11 Prolle Strona 20 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: