English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 20 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Printing a replacement part, and minor 1st pri... Por RandyM9 on Feb 15, 23 1427 8 Culprit First layer - very unsatisfactory results Answered Por karl-herbert on Feb 14, 23 1410 4 skaddisbladis Test print looks a bit odd Por Diem on Feb 14, 23 1447 7 elan Fresh setup – continuous beeping Por Diem on Feb 13, 23 1816 4 Wolf Stringing worse than my ender 3 with same sett... Por danifrancescon on Feb 12, 23 2022 7 danifrancesco... First layer not constant in time Por gagou7 on Feb 12, 23 1214 5 gagou7 Newbie question regarding z-axis calibration Answered Por James McCullou... on Feb 11, 23 1515 10 James McCullo... clogged nozzle on mk3s+ Por Robin on Feb 10, 23 1510 2 RMIL loud x axis motor Por Hello on Feb 09, 23 1456 2 Dawnbringer6 Warping and temporary layer shift Answered Por Mihai Dincules... on Feb 07, 23 1319 4 Mihai Dincule... Trouble with Z calibration? Por Matt Sheets on Feb 05, 23 1071 3 Matt Sheets Z wobbling and shifted layer on overhangs Por Thomas Cheng on Feb 04, 23 1841 12 Thomas Cheng hotted temp not settling even after a PID Por Hello on Feb 03, 23 1081 2 willeykj Missin top layer? Por karl-herbert on Feb 03, 23 1430 13 GrandPa Dragging through layer Por Jonathan Leek on Feb 02, 23 1370 3 Jonathan Leek Weird finish on first layer Answered Por Toochi on Feb 02, 23 1318 3 Toochi Printing a tube 120 mm diameter - print is und... Por SG Newb Rider on Feb 01, 23 1685 11 Prolle Smooth first print problem Por SG Newb Rider on Feb 01, 23 1149 2 Prusajeff28 Replacing nozzle. Answered Por Robin on Feb 01, 23 1284 5 Erwinv First layer problems - new printer (assembled ... Answered Por Jay Newman on Jan 31, 23 1469 5 Jay Newman Página 20 / 216 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Siguiente Compartir: