English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 20 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Printing a replacement part, and minor 1st pri... Von RandyM9 on Feb 15, 23 1426 8 Culprit First layer - very unsatisfactory results Answered Von karl-herbert on Feb 14, 23 1410 4 skaddisbladis Test print looks a bit odd Von Diem on Feb 14, 23 1447 7 elan Fresh setup – continuous beeping Von Diem on Feb 13, 23 1816 4 Wolf Stringing worse than my ender 3 with same sett... Von danifrancescon on Feb 12, 23 2022 7 danifrancesco... First layer not constant in time Von gagou7 on Feb 12, 23 1214 5 gagou7 Newbie question regarding z-axis calibration Answered Von James McCullou... on Feb 11, 23 1514 10 James McCullo... clogged nozzle on mk3s+ Von Robin on Feb 10, 23 1510 2 RMIL loud x axis motor Von Hello on Feb 09, 23 1455 2 Dawnbringer6 Warping and temporary layer shift Answered Von Mihai Dincules... on Feb 07, 23 1319 4 Mihai Dincule... Trouble with Z calibration? Von Matt Sheets on Feb 05, 23 1071 3 Matt Sheets Z wobbling and shifted layer on overhangs Von Thomas Cheng on Feb 04, 23 1839 12 Thomas Cheng hotted temp not settling even after a PID Von Hello on Feb 03, 23 1081 2 willeykj Missin top layer? Von karl-herbert on Feb 03, 23 1430 13 GrandPa Dragging through layer Von Jonathan Leek on Feb 02, 23 1370 3 Jonathan Leek Weird finish on first layer Answered Von Toochi on Feb 02, 23 1318 3 Toochi Printing a tube 120 mm diameter - print is und... Von SG Newb Rider on Feb 01, 23 1684 11 Prolle Smooth first print problem Von SG Newb Rider on Feb 01, 23 1149 2 Prusajeff28 Replacing nozzle. Answered Von Robin on Feb 01, 23 1284 5 Erwinv First layer problems - new printer (assembled ... Answered Von Jay Newman on Jan 31, 23 1469 5 Jay Newman Seite 20 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Teilen: