English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 18 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author 3D printer Test 3rd gen help Przez Diem on Mar 27, 23 1242 2 Michael Malen... Sliding(?) while printing Przez Diem on Mar 26, 23 1637 7 jeffkahn72 Process for replacing extrudeur body R6 Przez Yann04 on Mar 25, 23 1315 1 Yann04 Overhanging corners drooping/one corner rising Przez Mitch Gleed on Mar 25, 23 4321 7 jk1 Warping on first print Przez EHB on Mar 23, 23 1757 8 EHB Z-Axis noise. Is this normal? Przez LeeroyLee on Mar 21, 23 10072 15 Muldjord Left-hand z-axis motor not running Answered Przez Diem on Mar 19, 23 1439 9 Tommy York Filament runs out of nozzle when preheating Przez Netpackrat on Mar 18, 23 2232 7 Dynamo First layers outcomes vary with no changes? Answered Przez JOATZ on Mar 18, 23 1562 2 JOATZ First layer problem only with circles Przez broconne on Mar 18, 23 1809 10 broconne Ugly surface and holes [ABS] Przez p.siekierka on Mar 17, 23 1195 5 p.siekierka First print after assembly, layer shift Answered Przez Martian35g on Mar 16, 23 1701 4 Martian35g Skip on X and Y Axis during belt test? Przez John Bishop on Mar 15, 23 1761 4 Clarmrrsn Leveling probe tries to probe outside the bed Przez JoanTabb on Mar 14, 23 2069 4 Måns Henrikss... Strange under-extrusion Przez Diem on Mar 12, 23 1354 4 Robert Górski Very thick wires on first layer calibration te... Przez gilesjuk on Mar 12, 23 1271 8 Gilbou Other z set options available? Przez Robin on Mar 09, 23 1152 2 Rich J 1st layer problems Przez Martin Brimson on Mar 07, 23 1242 7 Martin Brimso... What is this a symptom of? Answered Przez Human Firewall on Mar 07, 23 1186 5 Human Firewal... Stringing Przez Stephan S. on Mar 06, 23 1812 13 Stephan S. Strona 18 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: