English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author Broken Hotend Thermistor Wire By JMars on 13 hours ago 14292 8 Patrick Stringy Benchy Answered By DartagnanK on Sep 04 542 3 DartagnanK printhead does not extrude after an hour in pr... By Diem on Aug 29 635 2 Elzpirat Weird first layer issues Answered By Heather Mac Le... on Aug 21 13483 7 Skint007 Bed leveling/underextrusion By perspectives08... on Aug 20 853 1 perspectives0... XYZ Calibration failed, check axes By Maksim Drachov on Aug 16 11192 19 rgordon0 life adjust Z - my way Answered By Carolina Custo... on Aug 13 997356 1012 JeffJordan Old STL file needed By Neophyl on Aug 02 1117 3 Gavin Melvill... First layer starts then z calibration loop By Diem on Jul 25 1268 2 Juan David Horizontal layer lines (Z-Banding?) By Aaron O on Jul 18 14969 9 F.L.A.M Y-axis belt touching belt holder — is this nor... Answered By printing_stuff on Jul 10 1888 9 printing_stuf... I bought a used printer and can't tell if it's... By PrusaNewbie on Jul 10 3401 4 PrusaNewbie Y - Axis Failed Self Test: Wrong Y-Axis Servo ... By HYspd on Jul 06 4191 2 Fourninetysix Z-Axis noise. Is this normal? By Robin_13 on Jun 26 12739 19 Muldjord Y Axis Length Fail on Bear MK3S+ build By Kenyiro34 on Jun 20 2795 8 Blippio Test print doesn't print straight lines By JoanTabb on May 30 3347 7 madcyborg X-Axis Motor Cable Too Short / Binding the Z-A... By Criptop on May 30 5415 8 Matt Kurek Printer goes to centre of build plate after ev... Answered By Cwhite534 on May 23 3133 7 jhk22 2nd Print with PLA takeoff from the plate By JoanTabb on May 15 3104 8 Lakwell 0.6mm nozzle, bad quality, what is the root ca... By gigiga on May 06 5289 10 SeppoTakalo Page 1 / 217 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: