English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 26 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Tytuł Tematu Ostatni Post Widok Posty Author Vertical Scars Przez cwbullet on Aug 28, 21 1829 2 CommanderMoos... Looking for hints to what is causing PETG firs... Przez PrinterJohn on Aug 26, 21 2078 3 PrinterJohn Stringy Prints On 2 of 5 Prusa Mini+ Printers Przez GRIT Automatio... on Aug 23, 21 2160 5 GRIT Automati... Printer stops near the end Answered Przez Lupin on Aug 23, 21 1776 4 3dprintershop... New printer fails calibration on x axis Przez cwbullet on Aug 23, 21 1572 7 Stecco Debugging bad PETG prints that are messy and c... Przez Lupin on Aug 23, 21 3447 5 Alyssa Assembled yesterday. Broken PTFE tubing?? Przez AK on Aug 21, 21 2840 8 AK Printer keeps stopping mid print Przez DevNull8 on Aug 20, 21 3299 4 DevNull8 PLA Filament Stuck in Extruder, Won't Pull Out... Przez JMH714 on Aug 10, 21 2496 3 AlexLandherr Nothing happens when I adjust dial for Z Przez BogdanH on Aug 09, 21 1871 5 Trina Lankfor... SuperPinda Height Spec? First Layer issues wit... Przez theRascal on Aug 09, 21 2912 5 theRascal Filament dragging? Przez Diem on Aug 06, 21 3598 6 HelenaB First Layer Calibration Doesn't Remove Gaps Przez AlexLandherr on Aug 04, 21 1932 3 AlexLandherr Strange Needle in the IPA Wet Wipe Bag Przez 3Delight on Aug 03, 21 2005 2 AlexLandherr weird clock like ticking sound Przez Domoipod on Aug 03, 21 1911 1 Domoipod Filament getting stuck in hotend. Przez cwbullet on Aug 02, 21 4176 10 Gbutton First Layer Calibration. -1.800 still not enou... Przez JMH714 on Aug 02, 21 3012 16 weust What would be causing this "tearing" in my fir... Przez Faceroller on Aug 02, 21 2104 3 Faceroller X axis only partially works for a few seconds ... Przez JoanTabb on Aug 01, 21 2018 4 RicoNYS logo prints ok for first few layers, than was ... Przez JMH714 on Jul 30, 21 2436 11 gristleking Strona 26 / 55 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Następny Share: