English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa MINI & MINI+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 26 / 55 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Suivant Titre du sujet Dernier message Nombre de vues Messages Author Vertical Scars Par cwbullet on Aug 28, 21 1824 2 CommanderMoos... Looking for hints to what is causing PETG firs... Par PrinterJohn on Aug 26, 21 2073 3 PrinterJohn Stringy Prints On 2 of 5 Prusa Mini+ Printers Par GRIT Automatio... on Aug 23, 21 2160 5 GRIT Automati... Printer stops near the end Answered Par Lupin on Aug 23, 21 1771 4 3dprintershop... New printer fails calibration on x axis Par cwbullet on Aug 23, 21 1572 7 Stecco Debugging bad PETG prints that are messy and c... Par Lupin on Aug 23, 21 3438 5 Alyssa Assembled yesterday. Broken PTFE tubing?? Par AK on Aug 21, 21 2837 8 AK Printer keeps stopping mid print Par DevNull8 on Aug 20, 21 3287 4 DevNull8 PLA Filament Stuck in Extruder, Won't Pull Out... Par JMH714 on Aug 10, 21 2490 3 AlexLandherr Nothing happens when I adjust dial for Z Par BogdanH on Aug 09, 21 1870 5 Trina Lankfor... SuperPinda Height Spec? First Layer issues wit... Par theRascal on Aug 09, 21 2905 5 theRascal Filament dragging? Par Diem on Aug 06, 21 3594 6 HelenaB First Layer Calibration Doesn't Remove Gaps Par AlexLandherr on Aug 04, 21 1930 3 AlexLandherr Strange Needle in the IPA Wet Wipe Bag Par 3Delight on Aug 03, 21 2004 2 AlexLandherr weird clock like ticking sound Par Domoipod on Aug 03, 21 1909 1 Domoipod Filament getting stuck in hotend. Par cwbullet on Aug 02, 21 4174 10 Gbutton First Layer Calibration. -1.800 still not enou... Par JMH714 on Aug 02, 21 3003 16 weust What would be causing this "tearing" in my fir... Par Faceroller on Aug 02, 21 2101 3 Faceroller X axis only partially works for a few seconds ... Par JoanTabb on Aug 01, 21 2018 4 RicoNYS logo prints ok for first few layers, than was ... Par JMH714 on Jul 30, 21 2430 11 gristleking Page 26 / 55 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 Suivant Partager :