Prusa3D Forum

Notifications

Clear all

GroovyZ1K

Groupe: Enregistré

A(ont) rejoint: 2019/03/13

Eminent Member

	I let Slic3r update but now when I hook up my PC to my MK3S ... Dans le forum General discussion, announcements and releases	il y a 5 years
	I'm curious if the silver PLA filament is Prusament Silver o... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Quick update, after many attempts to dial in my Z offset usi... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Here is where we are at now. Bed adhesion is better than ev... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Forgot to mention, after the cold pull the nozzle looked new... Dans le forum How do I print this? (Printing help)	il y a 6 years
	An update! Once I got home and was feeling very mellow, I w... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Thinking I probably should have posted this in Hardware afte... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Been here. Went crazy. Found the following fixes: 1. The pi... Dans le forum Hardware, firmware and software help	il y a 6 years
	So, interestingly I flashed to 3.7.0 Sunday morning and had ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	If you just lifted the PTFE up and out the dust may still tr... Dans le forum How do I print this? (Printing help)	il y a 6 years
	One other possible source for under-extrusion is debris in t... Dans le forum How do I print this? (Printing help)	il y a 6 years
	those sides show up allot better in that picture. what happ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Just ran another NASA log in Prusa PLA after reverting the f... Dans le forum How do I print this? (Printing help)	il y a 6 years
	hope it helps. trouble shooting a mk3 single is fun...compar... Dans le forum How do I print this? (Printing help)	il y a 6 years
	maybe turning the temp up might help When it was back to w... Dans le forum How do I print this? (Printing help)	il y a 6 years
	as long as the nozzle has that small gap with the heater blo... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Not sure if it helps, but attached are the settings for Slic... Dans le forum How do I print this? (Printing help)	il y a 6 years
	This was the print before the trio of dolphins, and it looke... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I had the same thought on the nozzle gap. I took a look at ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	maybe the filament is building backpressure. did you calibra... Dans le forum How do I print this? (Printing help)	il y a 6 years

Page 1 / 2 Suivant

Statistiques du forum

559 Forums

62.9 K Sujets

442.9 K Messages

20 En-ligne

67.7 K Membres

Le dernier des messages: MK4s Upgrade Really Beneficial/Needed for MK4 with MMU3 Already Installed? Notre nouveau membre: pinklemonade Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé