Prusa3D Forum

Benachrichtigungen

Alles löschen

GroovyZ1K

Gruppe: Registriert

Beigetreten: 2019/03/13

Eminent Member

	I let Slic3r update but now when I hook up my PC to my MK3S ... Im Forum General discussion, announcements and releases	Vor 6 years
	I'm curious if the silver PLA filament is Prusament Silver o... Im Forum How do I print this? (Printing help)	Vor 6 years
	Quick update, after many attempts to dial in my Z offset usi... Im Forum How do I print this? (Printing help)	Vor 6 years
	Here is where we are at now. Bed adhesion is better than ev... Im Forum How do I print this? (Printing help)	Vor 6 years
	Forgot to mention, after the cold pull the nozzle looked new... Im Forum How do I print this? (Printing help)	Vor 6 years
	An update! Once I got home and was feeling very mellow, I w... Im Forum How do I print this? (Printing help)	Vor 6 years
	Thinking I probably should have posted this in Hardware afte... Im Forum How do I print this? (Printing help)	Vor 6 years
	Been here. Went crazy. Found the following fixes: 1. The pi... Im Forum Hardware, firmware and software help	Vor 6 years
	So, interestingly I flashed to 3.7.0 Sunday morning and had ... Im Forum How do I print this? (Printing help)	Vor 6 years
	If you just lifted the PTFE up and out the dust may still tr... Im Forum How do I print this? (Printing help)	Vor 6 years
	One other possible source for under-extrusion is debris in t... Im Forum How do I print this? (Printing help)	Vor 6 years
	those sides show up allot better in that picture. what happ... Im Forum How do I print this? (Printing help)	Vor 6 years
	Just ran another NASA log in Prusa PLA after reverting the f... Im Forum How do I print this? (Printing help)	Vor 6 years
	hope it helps. trouble shooting a mk3 single is fun...compar... Im Forum How do I print this? (Printing help)	Vor 6 years
	maybe turning the temp up might help When it was back to w... Im Forum How do I print this? (Printing help)	Vor 6 years
	as long as the nozzle has that small gap with the heater blo... Im Forum How do I print this? (Printing help)	Vor 6 years
	Not sure if it helps, but attached are the settings for Slic... Im Forum How do I print this? (Printing help)	Vor 6 years
	This was the print before the trio of dolphins, and it looke... Im Forum How do I print this? (Printing help)	Vor 6 years
	I had the same thought on the nozzle gap. I took a look at ... Im Forum How do I print this? (Printing help)	Vor 6 years
	maybe the filament is building backpressure. did you calibra... Im Forum How do I print this? (Printing help)	Vor 6 years

Seite 1 / 2 Nächstes

Forums-Statistiken

559 Foren

63.1 K Themen

443.7 K Beiträge

23 Online

68 K Mitglieder

Letzter Beitrag: Nozzle Cleaning Failed Unser neuestes Mitglied: etiennep Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen