Prusa3D Forum

Avisos

Vaciar todo

GroovyZ1K

Grupo: Registrado

Registrado: 2019/03/13

Eminent Member

	I let Slic3r update but now when I hook up my PC to my MK3S ... En el foro General discussion, announcements and releases	hace 6 years
	I'm curious if the silver PLA filament is Prusament Silver o... En el foro How do I print this? (Printing help)	hace 6 years
	Quick update, after many attempts to dial in my Z offset usi... En el foro How do I print this? (Printing help)	hace 6 years
	Here is where we are at now. Bed adhesion is better than ev... En el foro How do I print this? (Printing help)	hace 6 years
	Forgot to mention, after the cold pull the nozzle looked new... En el foro How do I print this? (Printing help)	hace 6 years
	An update! Once I got home and was feeling very mellow, I w... En el foro How do I print this? (Printing help)	hace 6 years
	Thinking I probably should have posted this in Hardware afte... En el foro How do I print this? (Printing help)	hace 6 years
	Been here. Went crazy. Found the following fixes: 1. The pi... En el foro Hardware, firmware and software help	hace 6 years
	So, interestingly I flashed to 3.7.0 Sunday morning and had ... En el foro How do I print this? (Printing help)	hace 6 years
	If you just lifted the PTFE up and out the dust may still tr... En el foro How do I print this? (Printing help)	hace 6 years
	One other possible source for under-extrusion is debris in t... En el foro How do I print this? (Printing help)	hace 6 years
	those sides show up allot better in that picture. what happ... En el foro How do I print this? (Printing help)	hace 6 years
	Just ran another NASA log in Prusa PLA after reverting the f... En el foro How do I print this? (Printing help)	hace 6 years
	hope it helps. trouble shooting a mk3 single is fun...compar... En el foro How do I print this? (Printing help)	hace 6 years
	maybe turning the temp up might help When it was back to w... En el foro How do I print this? (Printing help)	hace 6 years
	as long as the nozzle has that small gap with the heater blo... En el foro How do I print this? (Printing help)	hace 6 years
	Not sure if it helps, but attached are the settings for Slic... En el foro How do I print this? (Printing help)	hace 6 years
	This was the print before the trio of dolphins, and it looke... En el foro How do I print this? (Printing help)	hace 6 years
	I had the same thought on the nozzle gap. I took a look at ... En el foro How do I print this? (Printing help)	hace 6 years
	maybe the filament is building backpressure. did you calibra... En el foro How do I print this? (Printing help)	hace 6 years

Página 1 / 2 Siguiente

Estadísticas del Foro

559 Foros

63.1 K Temas

443.7 K Respuestas

21 En línea

68 K Miembros

Último Mensaje: Nozzle Cleaning Failed Nuestro miembro más reciente: etiennep Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado