Prusa3D Forum

Notifications

Clear all

arosso

Groupe: Enregistré

A(ont) rejoint: 2018/10/21

Eminent Member

	I spent about 2 months getting this right on my MK3. Same is... Dans le forum Assembly and first prints troubleshooting	il y a 6 years
	Finally had some success. I think the following made the dif... Dans le forum How do I print this? (Printing help)	il y a 6 years
	The comments on the MVS made me go research this a bit more.... Dans le forum How do I print this? (Printing help)	il y a 6 years
	1. For my MVS I've set this to 5 mm^3/s. I had started at 9 ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I only tried 225C without Fan and that clogged too. I didn't... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I decided to push the temperature to 250C and switch off the... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Understanding Clogging - Carbon Fiber PLA Dans le forum How do I print this? (Printing help)	il y a 6 years
	I saw this too on my MK3S upgrade. They are just trying to d... Dans le forum Assembly and first prints troubleshooting	il y a 6 years
	Hmm... if the first layer seems even then I'm not sure. A fe... Dans le forum How do I print this? (Printing help)	il y a 6 years
	How does the first layer of the print look? I would try to s... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Yes, I've been keeping an eye on this a bit closer the last ... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I can't say I've experienced the magical adhesion properties... Dans le forum How do I print this? (Printing help)	il y a 6 years
	PEI Cleaning and Temperature Dans le forum How do I print this? (Printing help)	il y a 6 years
	My multi model print didn't go so well. The 'lip curl' I was... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I would assume that since the curling is due to heat just pa... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Thanks for the pointers. Yes, I've tried slowing things do... Dans le forum How do I print this? (Printing help)	il y a 6 years
	Is this a retraction problem or something else? Dans le forum How do I print this? (Printing help)	il y a 6 years
	The IPA I use is this one: . I'm not sure if they are requir... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I've been using those blue Scotts Shop paper towels: Maybe... Dans le forum How do I print this? (Printing help)	il y a 6 years
	I clean the sheet with Isopropyl alcohol (91%) each time. I'... Dans le forum How do I print this? (Printing help)	il y a 6 years

Page 1 / 2 Suivant

Statistiques du forum

559 Forums

62.9 K Sujets

442.8 K Messages

23 En-ligne

67.7 K Membres

Le dernier des messages: MK4S et MMU3 et TPU ?? Notre nouveau membre: pinklemonade Messages récents Messages non lus Balises

Icones du forum: Le forum ne contient pas de messages non lus Le forum contient des messages non lus

Icones du sujet: Sans réponse Repondu Actifs Au top Épinglé Non approuvé Résolu Privé Fermé