Prusa3D Forum

Benachrichtigungen

Alles löschen

arosso

Gruppe: Registriert

Beigetreten: 2018/10/21

Eminent Member

	I spent about 2 months getting this right on my MK3. Same is... Im Forum Assembly and first prints troubleshooting	Vor 6 years
	Finally had some success. I think the following made the dif... Im Forum How do I print this? (Printing help)	Vor 6 years
	The comments on the MVS made me go research this a bit more.... Im Forum How do I print this? (Printing help)	Vor 6 years
	1. For my MVS I've set this to 5 mm^3/s. I had started at 9 ... Im Forum How do I print this? (Printing help)	Vor 6 years
	I only tried 225C without Fan and that clogged too. I didn't... Im Forum How do I print this? (Printing help)	Vor 6 years
	I decided to push the temperature to 250C and switch off the... Im Forum How do I print this? (Printing help)	Vor 6 years
	Understanding Clogging - Carbon Fiber PLA Im Forum How do I print this? (Printing help)	Vor 6 years
	I saw this too on my MK3S upgrade. They are just trying to d... Im Forum Assembly and first prints troubleshooting	Vor 6 years
	Hmm... if the first layer seems even then I'm not sure. A fe... Im Forum How do I print this? (Printing help)	Vor 6 years
	How does the first layer of the print look? I would try to s... Im Forum How do I print this? (Printing help)	Vor 6 years
	Yes, I've been keeping an eye on this a bit closer the last ... Im Forum How do I print this? (Printing help)	Vor 6 years
	I can't say I've experienced the magical adhesion properties... Im Forum How do I print this? (Printing help)	Vor 6 years
	PEI Cleaning and Temperature Im Forum How do I print this? (Printing help)	Vor 6 years
	My multi model print didn't go so well. The 'lip curl' I was... Im Forum How do I print this? (Printing help)	Vor 6 years
	I would assume that since the curling is due to heat just pa... Im Forum How do I print this? (Printing help)	Vor 6 years
	Thanks for the pointers. Yes, I've tried slowing things do... Im Forum How do I print this? (Printing help)	Vor 6 years
	Is this a retraction problem or something else? Im Forum How do I print this? (Printing help)	Vor 6 years
	The IPA I use is this one: . I'm not sure if they are requir... Im Forum How do I print this? (Printing help)	Vor 6 years
	I've been using those blue Scotts Shop paper towels: Maybe... Im Forum How do I print this? (Printing help)	Vor 6 years
	I clean the sheet with Isopropyl alcohol (91%) each time. I'... Im Forum How do I print this? (Printing help)	Vor 6 years

Seite 1 / 2 Nächstes

Forums-Statistiken

559 Foren

62.9 K Themen

442.8 K Beiträge

23 Online

67.7 K Mitglieder

Letzter Beitrag: How to interpret ‘Width’ in the legend PrusaSlicer? Unser neuestes Mitglied: pinklemonade Neueste Beiträge Ungelesene Beiträge Schlagwörter

Forum Icons: Das Forum enthält keine ungelesenen Beiträge Das Forum enthält ungelesene Beiträge

Themen-Icons: Unbeantwortet Beantwortet Aktiv Heiß Oben angepinnt Nicht genehmigt Gelöst Privat Geschlossen