Prusa3D Forum

Avisos

Vaciar todo

arosso

Grupo: Registrado

Registrado: 2018/10/21

Eminent Member

	I spent about 2 months getting this right on my MK3. Same is... En el foro Assembly and first prints troubleshooting	hace 6 years
	Finally had some success. I think the following made the dif... En el foro How do I print this? (Printing help)	hace 6 years
	The comments on the MVS made me go research this a bit more.... En el foro How do I print this? (Printing help)	hace 6 years
	1. For my MVS I've set this to 5 mm^3/s. I had started at 9 ... En el foro How do I print this? (Printing help)	hace 6 years
	I only tried 225C without Fan and that clogged too. I didn't... En el foro How do I print this? (Printing help)	hace 6 years
	I decided to push the temperature to 250C and switch off the... En el foro How do I print this? (Printing help)	hace 6 years
	Understanding Clogging - Carbon Fiber PLA En el foro How do I print this? (Printing help)	hace 6 years
	I saw this too on my MK3S upgrade. They are just trying to d... En el foro Assembly and first prints troubleshooting	hace 6 years
	Hmm... if the first layer seems even then I'm not sure. A fe... En el foro How do I print this? (Printing help)	hace 6 years
	How does the first layer of the print look? I would try to s... En el foro How do I print this? (Printing help)	hace 6 years
	Yes, I've been keeping an eye on this a bit closer the last ... En el foro How do I print this? (Printing help)	hace 6 years
	I can't say I've experienced the magical adhesion properties... En el foro How do I print this? (Printing help)	hace 6 years
	PEI Cleaning and Temperature En el foro How do I print this? (Printing help)	hace 6 years
	My multi model print didn't go so well. The 'lip curl' I was... En el foro How do I print this? (Printing help)	hace 6 years
	I would assume that since the curling is due to heat just pa... En el foro How do I print this? (Printing help)	hace 6 years
	Thanks for the pointers. Yes, I've tried slowing things do... En el foro How do I print this? (Printing help)	hace 6 years
	Is this a retraction problem or something else? En el foro How do I print this? (Printing help)	hace 6 years
	The IPA I use is this one: . I'm not sure if they are requir... En el foro How do I print this? (Printing help)	hace 6 years
	I've been using those blue Scotts Shop paper towels: Maybe... En el foro How do I print this? (Printing help)	hace 6 years
	I clean the sheet with Isopropyl alcohol (91%) each time. I'... En el foro How do I print this? (Printing help)	hace 6 years

Página 1 / 2 Siguiente

Estadísticas del Foro

559 Foros

63.1 K Temas

443.9 K Respuestas

18 En línea

68.1 K Miembros

Último Mensaje: MK4S high flow nozzle and lack of power Nuestro miembro más reciente: etiennep Últimos Mensajes Publicaciones sin leer Etiquetas

Iconos del foro: El foro no contiene publicaciones sin leer El foro contiene publicaciones sin leer

Iconos de los Temas: No respondidos Respondido Activo Popular Fijo No aprobados Resuelto Privado Cerrado