PrusaSlicer hard to remove supports
 
Benachrichtigungen
Alles löschen

PrusaSlicer hard to remove supports  

Seite 7 / 8
  RSS
RD2-3D
(@rd2-3d)
Active Member
RE: PrusaSlicer hard to remove supports

Thanks Joan, I had missed the post adapting the parameters to the new settings. Everything is clearer now.

Thanks anyway

Veröffentlicht : 28/06/2022 6:00 am
Morpheus31
(@morpheus31)
Active Member
RE: PrusaSlicer hard to remove supports

Following up on this.  Would you please upload a snapshot of all your settings?  Appreciate it.

Posted by: @cwbullet

I am out of town for 10 days.  I will do so when I return.  

 

Veröffentlicht : 05/07/2022 7:33 pm
IceKillFX57
(@icekillfx57)
New Member
RE: PrusaSlicer hard to remove supports

yes, please make a Screenshot with Prusa 2.4.2

Veröffentlicht : 18/07/2022 8:40 am
cwbullet
(@cwbullet)
Mitglied
RE: PrusaSlicer hard to remove supports

Here you go.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 18/07/2022 9:10 am
Midi86
(@midi86)
New Member
RE: PrusaSlicer hard to remove supports

Interface pattern spacing should be 0.3mm, not 3mm right?

Posted by: @cwbullet

Here you go.  

 

Veröffentlicht : 16/08/2022 9:02 am
Neophyl
(@neophyl)
Illustrious Member
RE: PrusaSlicer hard to remove supports

In my book yes, personally I wouldn't have the interface that widely spaced.  Many support settings come down to personal preference but I also increase the interface layers from 2 to 4.  I find that printing a thicker section of interface makes it easier to remove in one piece as it doesn't break up as much and will sort of peel off easier. 

Veröffentlicht : 16/08/2022 9:10 am
kevman
(@kevman)
Estimable Member
RE: PrusaSlicer hard to remove supports

these settings are working out pretty good for me on snug supports.

 

Veröffentlicht : 21/08/2022 2:29 am
Daniel Petcu gefällt das
Daniel Petcu
(@daniel-petcu)
New Member
RE:

Thank you very much @bobstro .It worked very well for Colorfabb TPU Varioshore. 

Any suggestion on how can I improve the surface quality after removing supports?

Thank you in advance!

Diese r Beitrag wurde geändert Vor 2 years 3 mal von Daniel Petcu
Veröffentlicht : 25/09/2022 1:18 pm
cwbullet
(@cwbullet)
Mitglied
RE: PrusaSlicer hard to remove supports

I have noticed that PETG seems to fuse more than other filaments.  

I am trying to print one of these: 

https://www.thingiverse.com/thing:4600247

I guess I need to adjust my orientation.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 25/10/2022 10:21 am
cwbullet
(@cwbullet)
Mitglied
RE: PrusaSlicer hard to remove supports

I printed out of ASA with Bob's settings, and it is almost perfect.  Just a little cleanup on the overhand.  The enemy of good is better.  

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 26/10/2022 1:21 am
Zee
 Zee
(@zee)
Active Member
RE: PrusaSlicer hard to remove supports

Has anyone played around with settings for the organic supports yet? Trying this at the moment but they're still a bit hard to remove:

Veröffentlicht : 12/04/2023 11:10 am
kevman
(@kevman)
Estimable Member
RE: PrusaSlicer hard to remove supports

I read somewhere that top interface layers need to be zero for organic supports, I can't seem to find where I read this though...

Posted by: @zee

Has anyone played around with settings for the organic supports yet? Trying this at the moment but they're still a bit hard to remove:

 

Veröffentlicht : 12/04/2023 12:52 pm
Neophyl
(@neophyl)
Illustrious Member
RE: PrusaSlicer hard to remove supports

You read it in the release notes.  

"The Organic supports currently pose the following limitations:

For large models with a lot of supports, 16GB RAM minimum is recommended.
Top / bottom vertical separation distances are rounded to multiples of layer height.
Variable layer height is not supported.
Interface layers are not always produced reliably. As of now printing with zero interface layers is recommended, which produces easy to remove supports.
Rafts with Organic supports are buggy."

Veröffentlicht : 12/04/2023 1:12 pm
Zee
 Zee
(@zee)
Active Member
RE: PrusaSlicer hard to remove supports

OK thanks. I missed that part of the release notes. 

Veröffentlicht : 12/04/2023 2:48 pm
cwbullet
(@cwbullet)
Mitglied
RE: PrusaSlicer hard to remove supports

I plan to look at these those week.  I would appreciate anyone with good settings for supports. 

Posted by: @neophyl

You read it in the release notes.  

"The Organic supports currently pose the following limitations:

For large models with a lot of supports, 16GB RAM minimum is recommended.
Top / bottom vertical separation distances are rounded to multiples of layer height.
Variable layer height is not supported.
Interface layers are not always produced reliably. As of now printing with zero interface layers is recommended, which produces easy to remove supports.
Rafts with Organic supports are buggy."

 

--------------------
Chuck H
3D Printer Review Blog

Veröffentlicht : 12/04/2023 2:52 pm
Zee
 Zee
(@zee)
Active Member
RE:

This works for me, comes off easily with a print I tried last night.

 

Veröffentlicht : 13/04/2023 10:55 am
Neophyl
(@neophyl)
Illustrious Member
RE: PrusaSlicer hard to remove supports

You forgot to mention what material you were using with those settings.  PLA behaves different to PETG for example.  

Veröffentlicht : 13/04/2023 11:12 am
Zee
 Zee
(@zee)
Active Member
RE:

Apologies. It didn't allow me to edit past 5 minutes or so and I got distracted with another task afterwards and I felt annoyed at having to retype this out again.

Overture PETG (White), 0.6mm nozzle, 0.25 layer height. Tested on 0.75 extrusion width, 230/235C temperature settings. Extrusion multiplier 14, most speeds on 70 mm/s. Small perimeters 56%, External perimeters 77%, Top solid infill 45%.

To get bridging right I had to slow the dynamic overhang speeds to 10/10/15/20 and to disable the 'don't support bridges' option. Fan cooling is 100% for overhangs. Otherwise the prototype was leaking water.

To reduce print times increased the angles to 45/50 for preferred/max. In total this profile brings down print times from 22h for my print to 9h40min or so - inclusive of supports. Otherwise 7h vs 10h stock (0.3mm stock, just changed layer height to 0.25 and sliced). Still optimising but acceptable quality, at least for my prototyping. Attempting a new print as we speak with 0.9mm width and 80 mm/s; other settings as stated above. Hopefully all goes well.

Hope that helps.

Zhao.

 

Veröffentlicht : 13/04/2023 1:14 pm
Zee
 Zee
(@zee)
Active Member
RE: PrusaSlicer hard to remove supports

OK, I can't edit the thing anymore because my previous post is awaiting moderation. I can appreciate why this is implemented but that doesn't make it any less bloody annoying. There was an error in my previous post - its not extrusion multiplier that's 14, its max volumetric speed @ 14. Extrusion multiplier used is 1.05.

Veröffentlicht : 13/04/2023 1:22 pm
plotkin
(@plotkin)
Mitglied
RE: PrusaSlicer hard to remove supports

I came to ask the same thing with 0.8 nozzle kinda lost honestly.

I'm using bobstro settings anyways with organic supports.

Veröffentlicht : 06/08/2023 4:36 am
Seite 7 / 8
Teilen: