English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Strona 92 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Tytuł Tematu Ostatni Post Widok Posty Author thread and PETG Przez Si Powers on Feb 21, 21 12394 11 Tonino Designing in Autodesk 3D max Przez cwbullet on Feb 21, 21 2748 6 Lamita Complex Part Design Przez Yngeinstn on Feb 21, 21 4057 21 Yngeinstn Printing 3D plane - 1 layer walls with 0 botto... Przez navillus5 on Feb 21, 21 3644 8 navillus5 Bulge remedied but still exists as an overall ... Przez bobstro on Feb 20, 21 4472 14 jurassic73 Basic Print Parameters for Colorfabb PA-NEAT N... Przez stephen.o7 on Feb 19, 21 2354 1 stephen.o7 Improving outer (inner) part of a print Przez bobstro on Feb 18, 21 5038 8 LucasRolff Vertical line (defect) on print surface (with ... Przez Dan Rogers on Feb 18, 21 1586 2 Pietro75 Spiral marking on cylinder print Przez Dan Rogers on Feb 18, 21 2230 6 LT Warping Help Przez towlerg on Feb 18, 21 2082 12 LeTo Basic Stringing Test Przez pietronet on Feb 18, 21 5127 3 stwlam Suggestions on Supports? Answered Przez Redstick on Feb 18, 21 2248 6 Redstick stops extruding Przez Peter M on Feb 17, 21 1503 5 Delboy Booth The first 2 layers seem to shrink a bit more t... Przez Greg on Feb 16, 21 2890 3 Greg Approach to Exotic Materials Przez FoxRun3D on Feb 16, 21 1851 5 Sink Problem with the steel plate Answered Przez Claes B on Feb 15, 21 3686 12 Wassini Filamentum CPE HG100 Catching and knocking pri... Przez Shaughn on Feb 15, 21 2808 9 Shaughn Support as the "base" layers Przez Kendred Cooper on Feb 15, 21 1710 5 Kendred Coope... First print in vase mode Przez Dan Rogers on Feb 12, 21 1617 2 mrmpro ASA detaching from support Przez Orthonormal on Feb 12, 21 7714 8 Orthonormal Strona 92 / 190 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Następny Share: