English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 92 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Improving outer (inner) part of a print Da bobstro on Feb 18, 21 4799 8 LucasRolff Vertical line (defect) on print surface (with ... Da Dan Rogers on Feb 18, 21 1522 2 Pietro75 Spiral marking on cylinder print Da Dan Rogers on Feb 18, 21 2162 6 LT Warping Help Da towlerg on Feb 18, 21 2011 12 LeTo Basic Stringing Test Da pietronet on Feb 18, 21 5060 3 stwlam Suggestions on Supports? Answered Da Redstick on Feb 18, 21 2118 6 Redstick stops extruding Da Peter M on Feb 17, 21 1423 5 Delboy Booth The first 2 layers seem to shrink a bit more t... Da Greg on Feb 16, 21 2785 3 Greg Approach to Exotic Materials Da FoxRun3D on Feb 16, 21 1760 5 Sink Problem with the steel plate Answered Da Claes B on Feb 15, 21 3566 12 Wassini Filamentum CPE HG100 Catching and knocking pri... Da Shaughn on Feb 15, 21 2713 9 Shaughn Support as the "base" layers Da Kendred Cooper on Feb 15, 21 1649 5 Kendred Coope... First print in vase mode Da Dan Rogers on Feb 12, 21 1552 2 mrmpro ASA detaching from support Da Orthonormal on Feb 12, 21 7263 8 Orthonormal Blobs with Prusament PETG Da daniel.r3 on Feb 11, 21 3815 6 daniel.r3 Save time and filament by using reusable suppo... Da Dan Rogers on Feb 11, 21 2342 2 Husflid Problem with printing first layer of support s... Da Xaimav on Feb 11, 21 2270 7 belgovax Fixing spiral vase bridges? Da Honegod on Feb 10, 21 1908 3 Delarado How to fix a lack of filament at the seams in ... Da Lucas on Feb 10, 21 2402 3 Lucas Flat piece is detected as overhang in one leg Da FoxRun3D on Feb 10, 21 2550 11 Danielo Pagina 92 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: