English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Messages récents Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifications Clear all How do I print this? (Printing help) | RSS Page 82 / 190 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Suivant Titre du sujet Dernier message Nombre de vues Messages Author LaFactoriaV1 mask base in Sainsmart Pastel TPU... Par ssill2 on May 16, 21 2492 13 ssill2 Corner warp/lifting Par cwbullet on May 16, 21 3396 18 Jerry S Vase Mode with PETG Delaminates? Par Asraff Amzani on May 16, 21 11110 34 Asraff Amzani Top layer bulging outwards? Par -- on May 16, 21 2607 2 BulldogNine Bad print settings or poor design? Par -- on May 16, 21 1937 4 hawai The printout shifts by 10mm along the x-axis i... Par ssill2 on May 15, 21 3292 15 christian Voronoi Pattern Printing without strings possi... Par Swiss_Cheese on May 15, 21 4783 7 alexanderswo Please analyze print quality Par Swiss_Cheese on May 15, 21 3459 6 Astroxss TPE print problems Par Swiss_Cheese on May 13, 21 4042 16 DeltaWerks Need advice on troubleshooting my Benchy Par MightWorks on May 13, 21 4037 9 MightWorks Problems printing with PETG first layer. Par -- on May 13, 21 4716 15 Steve Gluing Help Par -- on May 12, 21 3063 9 Big Buddha Benchy printing problem with PETG Par Jimbo70 on May 12, 21 3280 6 Jimbo70 Printing with Prusa ABS-T Par cwbullet on May 12, 21 3079 4 shay.s 1st layer issue? Par Bob the Maker on May 12, 21 2049 4 Bob the Maker Corner warp/lifting Par cwbullet on May 11, 21 5500 5 Jerry S Weird noise and print failing at same spot Par dakiki on May 11, 21 2541 10 dakiki Brand New Official Hot End, Now Overhangs are ... Par cwbullet on May 10, 21 2895 16 TwoBallScrewB... Damaged in bottom printing Par -- on May 10, 21 2063 3 liubie Will printing nylon destroy my powder coated s... Par arjan on May 09, 21 17199 20 Tellblom Page 82 / 190 Précédent 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Suivant Partager :