English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 60 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Top solid infill doesn't extend under vertical... Da Swiss_Cheese on Jan 16, 22 2127 11 Connor Temp tower, no discernible difference Da Swiss_Cheese on Jan 16, 22 2409 4 Joey % of fill for printing MK3S parts Da FoxRun3D on Jan 16, 22 1659 7 cparfait How to get rid of horizontal lines? Da Diem on Jan 15, 22 3684 9 prusanewuser Problem with slinky (slingo) Da wombatjuggerna... on Jan 15, 22 2592 8 Joey Issues with ink globs mk3s Petg Da Diem on Jan 15, 22 2189 8 jherre6 cant get print to stick on build plate Answered Da Swiss_Cheese on Jan 14, 22 5907 26 Thgis Does this ASA seem right to you? Da Titan on Jan 14, 22 2722 3 Titan Tolerance of parts that should just tightly "s... Da deepblue4200 on Jan 14, 22 8770 7 deepblue4200 Inner print layer effecting outer wall Da Chris C on Jan 13, 22 1571 3 Chris C Kalibrování během tisku ?? Da Zoltan on Jan 13, 22 1659 2 Mareczech Very poor print quality on underside of ABS ev... Answered Da jrdpiper on Jan 12, 22 10445 36 jrdpiper Recommendations/rules of thumb for printing Ta... Da Swiss_Cheese on Jan 12, 22 25595 15 Robin Lithophane print has a ton of stringing and we... Da Robin on Jan 12, 22 3718 2 jinhao Fuzzy layers when printing calibration cube Da Robinf on Jan 12, 22 2638 1 Robinf Overhangs curls up Da Wout on Jan 10, 22 4589 3 Wout Printing Extrudr PETG comes off. Answered Da Smutje on Jan 10, 22 2295 6 deepblue4200 TPU - 1st layer calibration is working, 1st la... Da Bartosz Sobcza... on Jan 09, 22 5807 5 failed3dprint Top layer issues Da Charel Rommelf... on Jan 09, 22 2010 1 Charel Rommel... How do I get supports in an inside cavity at t... Da jrdpiper on Jan 08, 22 2297 1 jrdpiper Pagina 60 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: