English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Post recenti Announcements Forum English forum Original Prusa i3 MK3 & MK3S & MK3S+ How do I print this? (Printing help) Notifiche Cancella tutti How do I print this? (Printing help) | RSS Pagina 28 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Titolo discussione Ultimi post Visualizzazioni Post Author Just Bad Prints Da Jeffrey Dawson on Mar 29, 23 1314 1 Jeffrey Dawso... Issues with printing file Da Evgeniy on Mar 29, 23 1428 1 Evgeniy top layer warping on box Da Blarge1513 on Mar 29, 23 1354 1 Blarge1513 Curling & Nozzle crash issues with specific mo... Da frost on Mar 28, 23 2041 3 frost Flame-Retardant Capabilities Da Stefan on Mar 28, 23 1963 2 BParr4 Issue printing simple 3 part design Da FoxRun3D on Mar 27, 23 1744 2 Chris Print speed by layer Answered Da addohm on Mar 27, 23 3543 10 addohm Printing hoverangs in a corkscrew conveyor Da Galinette on Mar 25, 23 1797 1 Galinette Reducing staircase effect without lowering the... Da Galinette on Mar 24, 23 1586 1 Galinette Issue with rough top infill edges on 0.6mm noz... Da Mark Hähnel on Mar 22, 23 1545 1 Mark Hähnel Issues printing TPU Da ssill2 on Mar 20, 23 8507 14 Slayer Looks good, prints bad Da Rajah on Mar 20, 23 2011 5 Rajah Flat areas not consistent Da Diem on Mar 20, 23 2053 4 CupCap Vase Mode - Unexpected Nozzle Movement Answered Da broconne on Mar 19, 23 1492 4 broconne Print Wont stick to bed? curling sometimes Da jsw on Mar 19, 23 2662 7 cin05bus First layer suddenly stops sticking Answered Da zukpr on Mar 18, 23 3623 5 zukpr Black mark on prints Da viesturs on Mar 18, 23 16449 14 Phil Printing With NylonX Da Ridni Photo on Mar 17, 23 12005 20 alejo.v2 Print "block" Da Berne on Mar 17, 23 2115 9 Berne How to print the bottom layer optically as eve... Da Armin on Mar 15, 23 1787 1 Armin Pagina 28 / 190 Precedente 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 Avanti Condividi: