English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 97 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Layer inconsistency issues Por ZohMyGod on Oct 05, 20 1471 1 ZohMyGod XYZ calibration failed - Calibration Z issue Por ceceppa on Oct 04, 20 1859 6 ceceppa First Benchy print - advice appreciated! Por SteveS on Oct 04, 20 7152 5 QuokkaVibes First layer print fail time and time again, cl... Por Retired on Oct 04, 20 2603 7 chris.t25 Assembly Finished - Unable to feed filament in... Por pdirezze on Oct 03, 20 1911 7 pdirezze Problem with Model not sticking to Plate Por ekmek on Oct 03, 20 1925 8 Ford Ellis PINDA configuration and pre-flight check Por cwbullet on Oct 02, 20 2091 5 bobthechemist New MK3S Repeatedly Fails XYZ Calibration Answered Por cwbullet on Oct 02, 20 2247 6 rogers.doug First layers print OK but after 5mm or so it s... Por GKMAKEIT on Oct 02, 20 8052 18 muller.stepha... Curved frame Por cwbullet on Oct 02, 20 1746 2 godlike20 Benchy falling off halfway through print Por Peter M on Sep 30, 20 9505 10 Jeremy Makes failed 4-point bed calibration - what do I do ... Por Peter M on Sep 30, 20 1892 2 higonnet Perimeter gap between Start and End Por nikdo_nic on Sep 30, 20 11801 7 Ruan Bumps over text bridging on first few layers o... Por cwbullet on Sep 29, 20 2189 4 Joshua SElf test X axis failed Por karl-herbert on Sep 28, 20 1453 2 in-170 How are these first few prints? Por A.Awaji on Sep 28, 20 2722 6 cloudTechie Top of spires on castle went blobby Por ds21_old on Sep 28, 20 3308 4 Keith Cassidy Good benchy except top of rear window Por A.Awaji on Sep 28, 20 2950 3 kranebrain Slight layer shifting around the same Z-level Por cwbullet on Sep 28, 20 4054 2 Hydrologist Extruder clicking Por Roger on Sep 28, 20 2463 10 Roger Página 97 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: