English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 97 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Layer inconsistency issues Von ZohMyGod on Oct 05, 20 1471 1 ZohMyGod XYZ calibration failed - Calibration Z issue Von ceceppa on Oct 04, 20 1859 6 ceceppa First Benchy print - advice appreciated! Von SteveS on Oct 04, 20 7152 5 QuokkaVibes First layer print fail time and time again, cl... Von Retired on Oct 04, 20 2603 7 chris.t25 Assembly Finished - Unable to feed filament in... Von pdirezze on Oct 03, 20 1911 7 pdirezze Problem with Model not sticking to Plate Von ekmek on Oct 03, 20 1925 8 Ford Ellis PINDA configuration and pre-flight check Von cwbullet on Oct 02, 20 2091 5 bobthechemist New MK3S Repeatedly Fails XYZ Calibration Answered Von cwbullet on Oct 02, 20 2247 6 rogers.doug First layers print OK but after 5mm or so it s... Von GKMAKEIT on Oct 02, 20 8052 18 muller.stepha... Curved frame Von cwbullet on Oct 02, 20 1746 2 godlike20 Benchy falling off halfway through print Von Peter M on Sep 30, 20 9505 10 Jeremy Makes failed 4-point bed calibration - what do I do ... Von Peter M on Sep 30, 20 1892 2 higonnet Perimeter gap between Start and End Von nikdo_nic on Sep 30, 20 11801 7 Ruan Bumps over text bridging on first few layers o... Von cwbullet on Sep 29, 20 2189 4 Joshua SElf test X axis failed Von karl-herbert on Sep 28, 20 1453 2 in-170 How are these first few prints? Von A.Awaji on Sep 28, 20 2722 6 cloudTechie Top of spires on castle went blobby Von ds21_old on Sep 28, 20 3308 4 Keith Cassidy Good benchy except top of rear window Von A.Awaji on Sep 28, 20 2950 3 kranebrain Slight layer shifting around the same Z-level Von cwbullet on Sep 28, 20 4054 2 Hydrologist Extruder clicking Von Roger on Sep 28, 20 2463 10 Roger Seite 97 / 217 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Nächstes Teilen: