English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Forums English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Page 96 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Topic Title Last Post Views Posts Author First prints critique needed By Dink on Oct 14, 20 1441 1 Dink I think my PINDA Sensor has Failed By Fredericc on Oct 14, 20 3208 9 Jeff Sticking pattern on the surface of round objec... By Rahim42 on Oct 13, 20 1621 3 Rahim42 Lubricant prusa i3 mk3 By kasswassim on Oct 13, 20 1438 3 kasswassim First Layer Calibration is different from slic... By sophie.ke on Oct 13, 20 2557 6 sophie.ke Various printing issues / do I have a bad prin... By bobstro on Oct 12, 20 2091 2 bobcat19 Filament not extruding By ekmek on Oct 11, 20 17134 16 marcel.f2 MK3 Carriage screws By CopyRunStart on Oct 11, 20 1627 1 CopyRunStart MK3s New build. X axis failed By Mike on Oct 11, 20 1939 4 Mike Discrepancy between PRUSA test logo and Benchy By AWilling on Oct 11, 20 2000 1 AWilling Issue with Filamentum Crystal Clear By cwbullet on Oct 10, 20 4656 23 ceceppa Extruding too much filament before printing? By Andy on Oct 10, 20 9154 12 paul.a13 My first Benchy By KZG on Oct 09, 20 4464 11 KZG nylon guide assembly By Zoltan on Oct 09, 20 5587 6 gavin_the_new... First Layer Calibration Problem By GKMAKEIT on Oct 08, 20 2991 10 M.J. Caboose Am I squishing the first layer too much? By Ken S. on Oct 08, 20 4460 4 Ken S. First Layer Perimeter Errors By ealtabet on Oct 06, 20 2652 3 ealtabet X-axis layer shifts By JoanTabb on Oct 05, 20 1986 5 Vareax Printer retarts mid print By bobstro on Oct 05, 20 1222 4 John Layer inconsistency issues By ZohMyGod on Oct 05, 20 1456 1 ZohMyGod Page 96 / 217 Prev 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Next Share: