English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 94 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Tytuł Tematu Ostatni Post Widok Posty Author Crash after every print from SD, First Extrusi... Przez osmosis on Nov 01, 20 1825 4 osmosis What causes my needle holes? Przez karl-herbert on Oct 31, 20 1827 3 Infiltrator Brown Blobs after Nozzle Change Przez Neophyl on Oct 31, 20 3450 9 CrispyNacho Light stringing and large booger on presliced ... Przez John on Oct 30, 20 2771 3 John Broken heatbed cable cover Przez karl-herbert on Oct 30, 20 1848 4 Duncan Blackw... Cannot calibrate XYZ because dirty nozzel? Przez Ace on Oct 29, 20 4477 19 Ace Sample files from SD stop printing randomly at... Przez -- on Oct 29, 20 2254 8 Ropal Assembly Original Prusa i3 MK3S kit, 3 X-Axis ... Przez lonelymonk on Oct 29, 20 2489 13 lonelymonk Is my heatbed too hot for this filament? Answered Przez Neophyl on Oct 29, 20 2292 4 Infiltrator What are the white tubes included with the MK3... Przez Neophyl on Oct 29, 20 2016 3 Ace First layer ok, but other layers fail Przez Infiltrator on Oct 29, 20 3213 4 starblade Printing flex material Przez -- on Oct 28, 20 2337 4 Drunb X axis lenght error Przez Swisscore on Oct 28, 20 2540 10 FrancescaT I cant even print!! Przez kkuvam on Oct 28, 20 1712 8 kkuvam Problems / Tweaks needed after first couple pr... Przez RobSchaap on Oct 27, 20 1984 5 RobSchaap first layer problems Przez Denis Cowley on Oct 27, 20 1291 3 Denis Cowley First time turning on - After Language Selecti... Przez -- on Oct 27, 20 1414 3 Ace Bad quality over time Answered Przez JPLau001 on Oct 26, 20 3164 11 Tectonico3D Mission section in print, yet exists in previe... Przez vintagepc on Oct 26, 20 1556 5 alexsunny123 Really REALLY frustrated Przez -- on Oct 25, 20 2338 3 Infiltrator Strona 94 / 217 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Następny Share: