English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fóra English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Stránka 90 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Název Tématu Poslední Příspěvek Zobrazeno Příspěvky Author Trouble with first layer PTEG Od karl-herbert on Dec 06, 20 1694 4 ECUAdam First layer Od karl-herbert on Dec 06, 20 1293 3 Dekard65 Filament not feeding . pulley doesn't seem to ... Od Vera on Dec 06, 20 3028 7 Vera First Layer Inconsistencies Od sentientoctopi on Dec 06, 20 1812 6 sentientoctop... Help Please! First Layer Issues? Od JoanTabb on Dec 06, 20 3602 7 Jeff Under extrusion causing first layer cal proble... Od Der773 on Dec 06, 20 3017 10 Der773 Calibration issue Od Yossi on Dec 06, 20 1165 1 Yossi Does this look right? Od Niko.hogh on Dec 05, 20 2079 10 Niko.hogh Not much filament coming out of nozzle. Od bobstro on Dec 04, 20 1529 4 Russ Hotend / Nozzle? Problem with Filament Od karl-herbert on Dec 03, 20 1559 2 Anim Noisy bed Od Dan Rogers on Dec 02, 20 2286 3 xxorza Filament stuck and not able to remove PFTE Tub... Answered Od cwbullet on Dec 01, 20 4526 15 dehein2 BED TEMP jumps Od Lmmohr on Dec 01, 20 1473 8 Lmmohr first layer problems - is this bad adhesion or... Od oasixer on Dec 01, 20 1658 2 oasixer Prints fail when almost complete Od JoanTabb on Dec 01, 20 3014 11 Nihil PETG rough surface on portion of print Od DSM on Dec 01, 20 1867 1 DSM Horrible sounds coming from everywhere Od IKROWNI on Nov 30, 20 2956 12 IKROWNI MK3S Heatbed Noise Od Jack on Nov 30, 20 1662 3 Jack Get issues with all axis on calibration Od Kokort2 on Nov 30, 20 1299 1 Kokort2 Temperature Sensor Cables Plug In Answered Od JoanTabb on Nov 28, 20 2947 8 ndawghoodstar Stránka 90 / 217 Předchozí 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Další Share: