English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 86 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Bad adhesion printbed Por Yeshead on Jan 04, 21 2166 5 Yeshead Problems with printing circles Por Daniel10712 on Jan 04, 21 2924 8 Daniel10712 What is the factory measurements? Answered Por Kevin on Jan 03, 21 2015 6 Kevin MK3S+ PSU does not turn on - first assembly Por Diem on Jan 03, 21 1696 5 PT3D_enthusia... Power Up Failed - Sort of Por JoanTabb on Jan 03, 21 1627 9 Lynng MK3S+ Upgrade Kit Instructions Por Cynan on Jan 02, 21 1989 2 FJJ 3d Benchy problems Por Swiss_Cheese on Jan 02, 21 4201 5 Maassie88 hotend replacement Por eng.shaimaa.el... on Jan 01, 21 1686 2 eng.shaimaa.e... Printed parts good enough? Answered Por jsw on Jan 01, 21 1402 4 Cynan first layer small size Por Karel_G on Jan 01, 21 2506 2 Steve LCD Cycling Between Blue and Off on First Star... Por Masinka on Jan 01, 21 1802 3 Masinka Poor layer filling Answered Por Neophyl on Dec 31, 20 1683 5 DaleKramer boot recycling Answered Por reesys on Dec 31, 20 1427 3 reesys Tormented by blops & adhesion issues - Z calib... Por Gavin on Dec 30, 20 1842 7 Cocomon Unruly print bed Por tojake2 on Dec 30, 20 1519 4 tojake2 Extruder have friction x-axis Por kungkarl on Dec 29, 20 2418 1 kungkarl Y-Axis length calibration/belt test error Por evandcoleman on Dec 29, 20 1613 2 evandcoleman Question About Securing The Extruder Assembly ... Por Alan B. on Dec 28, 20 1079 2 Alan B. Problem reassembling bondtech Prusa i3 mk3 Por LtVonWitzland on Dec 28, 20 1438 8 LtVonWitzland Theoretical first layout height vs. actual lay... Por Peter M on Dec 28, 20 1601 7 grigro Página 86 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: