English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 6 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author First Layer Bubbling(?) in same spot on print ... Von SteveC on Mar 19 1727 12 SteveC Wavy Walls Von Max Schuh on Mar 17 5566 17 ellaine Bad first layer print Von Bob on Mar 14 1204 3 Michael Oakle... Weird offset / missteps on Z axis or extrusion... Von nio101 on Mar 10 1041 9 nio101 Another XYZ calibration fail Von troconn on Mar 09 4491 9 Asher Printing of prusa parts. Von Bob on Mar 07 1380 2 Wazfoodle Z axis calibration Answered Von Marek Jaros on Mar 06 1478 5 Marek Jaros X Shift on Recently upgraded mk3s+ Von Robin on Mar 06 1405 3 Graeme Johans... The Base Showing Up On The External Layer Von Robin on Mar 06 1337 2 LeeH Can't remove attached cable from motherboard..... Von bobnosn on Mar 03 3010 10 PrusaVA Calibration failed, check axis and run again Von Robin on Mar 01 1287 2 Kraut55 Extruder destroyed the PIDA mount Von Robin on Feb 28 1553 11 jlc1978 extruder stops turning mid print Von tigertrainer on Feb 27 1430 7 tigertrainer Extruder parks at 0 when print is done. Von Logan Elswick on Feb 24 1251 3 Logan Elswick First Layer Major Change Von Reed Bartlett on Feb 22 1248 7 Reed Bartlett XYZ calibration, Bed calibration point was not... Von Egor Sovtsov on Feb 22 22372 14 Kurosakidom Issue with Benchy Von Thejiral on Feb 21 1477 11 jdenver Upgrade order - Mk3S+MMU2S to MK3S+ or MK3S to... Answered Von JoanTabb on Feb 19 1431 6 lp3dprint X Axis Belt and Tension Answered Von Diem on Feb 18 3200 14 bambi Hotend not heating Von karl-herbert on Feb 15 1223 4 Kraut55 Seite 6 / 216 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Nächstes Teilen: