English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Neueste Beiträge Announcements Foren English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Benachrichtigungen Alles löschen Assembly and first prints troubleshooting | RSS Seite 5 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Titel des Themas Letzter Beitrag Ansichten Beiträge Author Printer Stand Von Diem on Dec 07, 24 2404 4 akerezy BOD - Fortunately this one was easy to fix Von jsw on Dec 05, 24 2064 1 jsw Stubborn extruder clog Von Diem on Dec 04, 24 2447 2 DK1474 First post! First issue too... 🙁 Von Robin on Nov 30, 24 2667 8 Faris Itum Print differences in x Direction Von Robin on Nov 29, 24 2517 2 raepton Temperatur / Stringing Von raepton on Nov 26, 24 2332 3 raepton Prints coming up and getting XY axis failure Von jbkmelk on Nov 21, 24 2149 3 jbkmelk first layer print quality Von gzhangx on Nov 18, 24 2952 13 gzhangx Leak at nozzle Von Diem on Nov 16, 24 1870 3 jlc1978 Printing starts well but eventually doesn't st... Von samuel.jimenez on Nov 14, 24 1565 2 samuel.jimene... How can I improve "stringing"? Von samuel.jimenez on Nov 14, 24 2854 16 samuel.jimene... Filament gets stuck during printing Von Szabolcs Siebe... on Nov 10, 24 1817 3 Szabolcs Sieb... inside perimeter not sticking to buildplate Answered Von disconnected on Nov 09, 24 2115 6 disconnected PLA not sticking??? Von Diem on Nov 04, 24 63353 85 travis.c5 Printer skips a few centimeters on start of ev... Von Mathew Baldwin on Oct 24, 24 7418 25 Justinas Is this bed leveling good? Von gzhangx on Oct 17, 24 2091 1 gzhangx Print quality was good, but not any more Von gzhangx on Oct 15, 24 2332 2 Stoffel First layer issues edges curling Von jbkmelk on Oct 15, 24 2296 3 jbkmelk Inconsistent Prusament ASA extrusion? Von Perro on Oct 06, 24 2696 5 Perro I made a mistake and updated my firmware. Ther... Von Robin on Oct 06, 24 2286 2 L P Seite 5 / 218 Vorherige 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 Nächstes Teilen: