English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Últimos Mensajes Announcements Foros English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Avisos Vaciar todo Assembly and first prints troubleshooting | RSS Página 69 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Título del Tema Último Mensaje Visitas Respuestas Author Strange noise when printing - MK3S+ Por Carlos Alberto on May 25, 21 2700 6 Carlos Albert... Horizontal Circles not round Por -- on May 25, 21 4910 8 PatrickM Filament not going in, new printer Por -- on May 25, 21 2399 11 Cold_Taco loose hotend? Por cwbullet on May 24, 21 6032 21 joe5939 Issue with printing with other brand PLA Por Ara on May 24, 21 1865 4 Ara What is wrong with this pic? Por cwbullet on May 23, 21 8069 44 Sink Extruder problem - new printer Por cwbullet on May 23, 21 1548 10 Vita Black plastic collet Por eng.shaimaa.el... on May 23, 21 3264 20 eng.shaimaa.e... Sloppy Delivery - Getting too big? Por cwbullet on May 22, 21 1975 7 Sink filament sensor Por cwbullet on May 22, 21 1482 4 wes Print defect mostly along one axis Por cwbullet on May 22, 21 1468 4 hamgolfer Repacking Misumi Bearings .. Replacing the fac... Por cwbullet on May 21, 21 2310 3 Sink Extruder Body: Stuck screw and Spinning M3NS n... Por MinorMatt on May 21, 21 4151 4 Seraphsins First Self-Test Failing at Bed Check Por -- on May 20, 21 3224 2 Nyvad Large gaps on the seam Answered Por DoctorShtein on May 19, 21 13235 8 DoctorShtein Extruder scoring the upper x-axis smooth rod? Por -- on May 18, 21 5429 32 Frank Prusament PETG not sticking to the bed Answered Por Felenari on May 18, 21 5420 19 Barca95 First Nozzle Change... advice? Por -- on May 18, 21 2374 4 MinorMatt Calibration problem Por chris on May 18, 21 2073 5 chris Is this cold pull OK? Por cwbullet on May 17, 21 4172 12 Peter M Página 69 / 217 Anterior 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 Siguiente Compartir: