English forum České fórum Polskie forum Forum Français Forum Italiano Foro Español Deutsches Forum Recent Posts Announcements Fora English forum Original Prusa i3 MK3 & MK3S & MK3S+ Assembly and first prints troubleshooting Notifications Clear all Assembly and first prints troubleshooting | RSS Strona 69 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Tytuł Tematu Ostatni Post Widok Posty Author Leaky nozzle - how much to disassemble? Przez -- on May 10, 21 1715 8 Paul New to 3D printing and Prusa Products. Is this... Przez Taxane on May 10, 21 2923 7 Taxane Assembly completed and first print Przez Andrew Weitzel on May 09, 21 1796 5 Andrew Weitze... Gap Fills Issue Przez Rocky79 on May 09, 21 3121 18 Rocky79 y axis bearing noise at initial assembly Przez cwbullet on May 08, 21 3384 8 john XYZ Calibration Issue Przez -- on May 08, 21 1354 8 MinorMatt MK3S+ printing fan not working - cannot comple... Przez Clarmrrsn on May 08, 21 2023 3 admpc scale units mm/inches Przez -- on May 07, 21 3496 7 Jerry S Fan not spinning Przez 3Delight on May 07, 21 3537 16 boulland.mich... Nozzle hits prints off after about 450mm Answered Przez cwbullet on May 07, 21 14537 46 Milazzone First print quality feedback Przez cwbullet on May 07, 21 1882 3 quody Test pattern is not sticking to heatbed Przez cwbullet on May 07, 21 3292 27 CJSHayward Can't get first layer right Answered Przez Veritas on May 07, 21 1696 5 Veritas Y-axis assembly issues / frame skew Przez -- on May 07, 21 2234 6 hullcb How do I slice the Stanford bunny for my MK3S+... Przez cwbullet on May 07, 21 2006 14 CJSHayward Z-screw covers Przez -- on May 06, 21 1498 3 MinorMatt Heatbed / Meshbed center is lower then left an... Przez -- on May 06, 21 1663 6 Stefan Build instructions terrible - could shave hour... Przez -- on May 06, 21 2511 17 Boslaw Small holes (underextrusion?) and errors on la... Przez -- on May 06, 21 2753 3 ishiharas First Layer Calibration Przez Kodiak437 on May 06, 21 1767 7 Kodiak437 Strona 69 / 216 Wstecz 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 Następny Share: